background image

 

ZP1-F Series Operation Manual 

Item 

Control/LED 

LED colour  Description 

 

— or — 

Evacuation 
Start/Stop button 
and LED for 
NBN S 21-100 

 

 

Activates or deactivates evacuation sounders. 

A steady LED indicates that evacuation sounders 
are active. 

16 

System Fault LED 

Yellow 

Indicates a control panel processor failure. 

17 

Out of Service LED 

Yellow 

Indicates that control panel power supply 
conditions put fire detection zones and inputs out 
of service. 

Other system functions remain operational 
(including networking and output activation). 

A steady yellow LED indicates that there is no 
mains power and the battery power is insufficient. 
A flashing yellow LED indicates that the mains 
power is insufficient and there is no battery 
power. 

18 

Earth Fault LED 

Yellow 

Indicates an earth isolation fault.  

19 

Supply Fault LED 

Yellow 

Indicates a fault with the power supply. 

A flashing LED indicates a battery or battery fuse 
fault. A steady LED indicates a mains or mains 
fuse fault. 

20 

Fire Routing Delay 
button and LED 

— or — 

Warning Sounder 
Delay for 
NBN S 21-100 

Yellow 

Enables or disables a previously configured fire 
routing or warning sounders delay. (For warning 
sounders, this cancels a delay as it counts down 
and activates sounders.) 

A steady LED indicates that a fire routing or 
warning sounders delay is configured and 
enabled. A flashing LED indicates that a fire 
routing or warning sounders delay is counting (fire 
routing will be activated when the configured 
delay elapses). 

21 

Fire Routing 
ON/ACK button and 
LED 

Red 

Cancels a previously configured delay and 
activates fire routing. 

A flashing LED indicates that fire routing has 
been activated. A steady LED indicates that the 
fire routing signal has been acknowledged by the 
remote monitoring equipment. 

 

— or — 

Warning Start/Stop 
button and LED for 
NBN S 21-100 

 

 

Activates or deactivates warning sounders. 

A steady LED indicates that warning sounders 
are active. 

22 

Fire Routing 
Fault/Disable/Test 
button and LED 

— or — 

Warning 
Fault/Disable/Test 
button and LED for 
NBN S 21-100 

Yellow 

Indicates that fire routing is in a fault condition, is 
disabled, or is being tested. 

A flashing LED indicates a fault. A steady LED 
indicates that the function is disabled or is being 
tested. 

Содержание zp1-f Series





























Отзывы: