Zimmer GEP2006IL-03 Скачать руководство пользователя

Страница: 11 / 44

7 Technical data

INFORMATION

►

You can find the information in the technical data sheet on our website.

This data varies within the series, depending on the specific design.

►

Please contact Zimmer Customer Service if you have any questions.

7.1

Electrical specifications

INFORMATION

►

You can find the information in the technical data sheet on our website.

This data varies within the series, depending on the specific design.

►

Please contact Zimmer Customer Service if you have any questions.

7.2 Protection class

NOTICE

The product achieves protection class IP40 in all mounted positions of installation.

8 Accessories/scope of delivery

INFORMATION

If any accessories not sold or authorized by Zimmer GmbH are used, the function of the product cannot be

guaranteed. Zimmer GmbH accessories are specifically tailored to the individual products.

►

For optional accessories and those included in the scope of delivery, refer to our website.

9 Transportation/storage/preservation

►

Transport and storage of the product must be done only with the original packaging.

►

If the product has already been installed on the superordinate machine unit, care must be taken during transport to

ensure that no unexpected movements can occur.

►

Before commissioning the product and after transport, check all power and communication connections as well as

all mechanical connections.

►

If the product is stored for an extended period, the following points are to be observed:

►

Keep the storage location as dust-free and dry as possible.

►

Avoid temperature fluctuations/observe and adhere to the temperature range.

►

Avoid wind/drafts/water condensation formation.

►

Cover the product with a weatherproof, tear-resistant foil to prevent dust.

►

Pack the product and do not expose it to direct sunlight during storage.

►

Clean all components. There must be no soiling left on the components.

►

Visually inspect all components.

►

Remove all foreign substances.

►

Properly remove potential corrosion spots.

►

Close electrical connections using suitable covers.

INSTALLATION AND OPERATING INSTRUCTIONS:

GEP2000IL-03

DDOC01219 / b

EN / 2021-12-20

Zimmer GmbH • Im Salmenkopf 5 •



77866 Rheinau, Germany •



+49 7844 9138 0 • www.zimmer-group.com

Содержание GEP2006IL-03













































Результаты поиска

Содержание GEP2006IL-03

Отзывы:

Похожие инструкции для GEP2006IL-03

Бренды по названию

Популярные бренды

Zimmer GEP2006IL-03, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEP2006IL-03

Отзывы:

Похожие инструкции для GEP2006IL-03

Бренды по названию

Популярные бренды