ZIEHL-ABEGG FXET4AMQ Скачать руководство пользователя страница 81

Страница: 81 / 87

Display

Code*

LED Code

Relais switches
**

Cause

Reaction of Controller

internal

Opera-
tion

Failure

Adjustment

Motor fault

Err

Tripping of connected ther-
mostat or break between
terminals

“

”

The unit then remains switched
off. A programmed operating
and fault-indicating relay is trig-
gering
Check motor and connection
then reset

External error

selecta-
ble

Alarm from external con-
tact

Device continues working un-
changed
check contacts

Lmt E1 min

selecta-
ble

Limit indication minimum
Actual value below setting

“

Alarm Minimum

”

(Input

“

”

)

Device continues working un-
changed
Check setting and sensor

Lmt E1 max.

selecta-
ble

Limit indication maximum
Actual value above setting

“

Alarm Maximum

”

(Input

“

”

)

Sensor 1

Msg or.
AL*

selecta-
ble

Interruption / short circuit
in the sensor leads or sen-
sor values measured are
outside measuring range

The device works with minimal
or maximum modulation de-
pending on whether there is a
short-circuit or an interruption,
and on the programmed mode
of operation.
Check sensor

Earth fault

Err

Shortcut earth, that means
Shortcut between one
motor wire and PE

The unit cuts out and does not
switch on again.
Disconnect the device from
mains.
Check motor wires

A permanent shortcut earth
can damage the device!

DC-Voltage

DC overvoltage because
of shortcut earth at switch-
on.

The unit cuts out.
Disconnect the device from
mains.
Check motor wires

*Code: Err = Error Al = Alarm Msg = Message
** Relais switches dependent on programmed function

Operating Instructions

Fcontrol

–

model series FXET4/6/10AMQ

Events / Fault signals

L-BAL-E079-GB 1706 Index 008

Part.-No.

81/87

Содержание FXET4AMQ
























































































Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды

ZIEHL-ABEGG FXET4AMQ, Руководство по эксплуатации

Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды