ZIEHL-ABEGG FXET4AMQ Скачать руководство пользователя страница 35

Страница: 35 / 87

9.3.2

Setting for operation modes

3.01

...

3.04

3.01

Pressure control condensers, setting Setpoint in bar

3.02

Pressure control for condensers with input for refrigerant, Setpoint in

3.03

Two sensors for dual circuit condenser. Automatic regulation to the highest pressure (selection ampli

ﬁ

integrated) operation display:

“

Control value

”

, Setpoint in bar

3.04

Two sensors for dual circuit condenser with input for refrigerant automatic regulation to the highest
pressure (selection ampli

ﬁ

er). Setpoint in

C , also for different refrigerants suitably there comparison of

the temperatures. Display during operation:

“

Control value

”

Setting

Setpoint1

3.01

and

3.03

Setting range: in measuring range of sensor, factory setting: 12.0 bar

3.02

and

3.04

Setting range: dependent on the selected refrigerant, factory setting:

35.0

Setpoint1

Setpoint2

Setting

“

Setpoint 2

”

e.g. reduced value for night operation.

Switch over Setpoint 1/2 by external contact (as long as no allocation is carried out:
Display:

- - - - -

IOSetup).

Pband

Narrow control range = Short control times
Wide control range = Longer control times and more stable control

3.01

and

3.03

Setting range: in measuring range of sensor, factory setting: 5.0 bar

3.02

and

3.04

Setting range: dependent on the selected refrigerant and in measuring

range of sensor, factory setting: 7.0 K

Pband

Min. Speed

(basic speed only when needed)

Setting range:

OFF

→

“

Shutdown Freq.

”

(

Motor Setup) -

“

Max. Speed

”

Factory setting:

OFF

Max. Speed

(speed limitation only when needed)

Setting range:

“

Max. Frequency

”

(

Motor Setup) -

“

Min. Speed

”

Factory setting: 50.0 Hz

Manual mode

“

OFF

”

= automatic control as function of the set parameters (Factory setting)

“

”

= automatic control without function, speed setting in menu

“

Speed manual

”

Speed manual

Manual speed setting without in

ﬂ

uence by the external signal.

Activation by menu

“

Manual mode

”

or external contact at digital input (

IO Setup).

Setting range: 0...

“

Max. Frequency

”

(

Motor Setup)

Factory setting: 50.0 Hz
For information about deactivated regulation the adjusted value for manual speed is
indicated alternating with the actual value.

Operating Instructions

Fcontrol

–

model series FXET4/6/10AMQ

Programming

L-BAL-E079-GB 1706 Index 008

Part.-No.

35/87

Содержание FXET4AMQ
























































































Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды

ZIEHL-ABEGG FXET4AMQ, Руководство по эксплуатации

Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды