ZIEHL-ABEGG FXET4AMQ Скачать руководство пользователя страница 12

Страница: 12 / 87

Type FXET6/10AMQ

Fastening at 4 points

GM00005A_M
15.12.2015

Drill fastening points

“

”

“

”

Fasten device with screws.

4.4

Cable inlet

Remove the terminal compartment cover.

Depending on the housing model cut off necessary cable inlets respectively to the cable diameter.
Or alternative use cable inlet for cable glands. Metal sheet housings are supplied with stoppers.
Any cable ducts openings not used must be sealed!

Strip and insert the cables properly.

Attach cover for terminal compartment again carefully before start-up.

Housing with aluminum base plate

Cable inlet with step nozzles (factory installed)

3 x max. 18 mm

3 x max. 14 mm

3 x max. 11 mm

4 / 8 x max. 8 mm

attached cable inlet for cable glands

17 / 21 mm

12.5 / 17 mm

Fastening screws

Information

•

Cable glands can be used alternatively (not included in delivery). The manufacturer

’

s speci

ﬁ

cations

for tightening torque and sealing area must be observed!

•

Openings which are not needed must be sealed!

Operating Instructions

Fcontrol

–

model series FXET4/6/10AMQ

Mounting

L-BAL-E079-GB 1706 Index 008

Part.-No.

12/87

Содержание FXET4AMQ
























































































Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды

ZIEHL-ABEGG FXET4AMQ, Руководство по эксплуатации

Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды