ZIEHL-ABEGG FXET4AMQ Скачать руководство пользователя страница 51

Страница: 51 / 87

9.10.2.2

Enable ON/OFF function

Remote ON/OFF (electronic disconnection) and Reset after a motor malfunction via

ﬂ

oating contact.

The power section is electronically disconnected. Operation of the device is still possible after
pressing the

“

Esc

”

hotkey combination in switched-off condition. Signal- in and outputs remain active.

•

A programmed operating indicator relay (factory set

“

K1 function

”

) reports the switch-off.

•

A programmed alarm relay (factory set

“

K2 function

”

2 K

) does not report the switch-off.

Display

STOP

for switch OFF

•

Controller

“

”

for closed contact (fac-

tory setting).

•

Controller

“

OFF

”

with opened contact

When inverting in reverse i.e. equipment

“

OFF

”

with closed contact.

Digital IN 1

OFF

10.05.2007

v_1d_freigabe_d1_d1.vsd

Contact at digital input e.g.

“

Digital In 1

”

Attention!
No disconnection (isolation) when turned off, in accordance with VBG4

6)!

9.10.2.3

External fault Function

Connecting an external alarm indication (via

ﬂ

oating contact). The device continues to work un-

changed during an external indication to the digital input; the alarm symbol appears in the display.
This indication can be issued via the relay contacts (K1, K2) (

IO Setup function K1, K2).

Example for connecting an external alarm indication e.g. to digital input

“

Digital In 1

”

Controller

1~ S-ET..
3~ STDT..

D1
D1

10.05.2007

v_2d_externe_stoerung_set_stdt.vsd

1~ S-ET..
3~ STDT..

•

Indication during closed contact (factory setting):

“

D1 Inverting

”

“

OFF

”

•

Indication during opened contact:

“

D1 Inverting

”

“

”

Actual value

Alarm symbol for indication

“

External fault

”

Operating Instructions

Fcontrol

–

model series FXET4/6/10AMQ

Programming

L-BAL-E079-GB 1706 Index 008

Part.-No.

51/87

Содержание FXET4AMQ
























































































Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды

ZIEHL-ABEGG FXET4AMQ, Руководство по эксплуатации

Результаты поиска

Содержание FXET4AMQ

Отзывы:

Бренды по названию

Популярные бренды