ZIEHL-ABEGG FXD32AM Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 123

background image

PINs

PIN

Function

PIN 0010

Opening service menu, if PIN-protection activated

PIN 1234

Opening

“

setting

”

.

if

“

set protection

”

=

“

ON

”

(

Controller Setup)

PIN 9090

Restore user setting

PIN 9091

Save user setting (corresponds function

“

Save user setup

”

=

“

ON

”

Controller Setup)

PIN 9095

Restore factory setting = delivery status

11

Diagnostics menu

Main menu

The diagnostics menu supplies information about the momentary operating condition
of the device.

IO Setup
Limits
Timer
Autoaddressing
Diagnostic

000419:27:28

Runtime Controller

Operating hours on the line

The time counter (h:m:s) runs as soon as line voltage is applied to the device and the
device is switched on (without failure).
If events step on (Motor fault, External Error, etc.), the period of operation is stored at
this time (

Protocol).

000146:23:54

Runtime Motor

Operating hours with modulation

The time counting (h:m:s) runs only when a modulation of the controller is present

585 V

DC-Voltage

DC-Voltage

The intermediate circuit voltage without load is the peak value of the input voltage.
In a three-phase supply network with 400 V, an intermediate circuit voltage of ca. 565 V
results. This voltage sinks slightly under load.

400 V

Line voltage

Line voltage

28.1

°

C

IGBT temperature

IGBT temperature

Display of the internal temperature of the power semiconductor. At impermissibly high
temperatures (from 90

°

C), the output power is automatically reduced. The device is

switched off at 105

°

C.

29.5

°

C

Filterchoke

Filterchoke

Temperature display for input choke.
At impermissibly high temperatures, the output power is reduced or the device switched
off.

30.1

°

C

Sine

ﬁ

lter

Sine

ﬁ

lter

Display of sine

ﬁ

lter choke temperature. In case of temperature increase above prede-

termined threshold value the modulation is switched off. Restart when cooled down!
(only in version with integrated sine

ﬁ

lter)

20.0

°

C

E1 - KTY

E1

Signal height at analog input E1 (Analog In 1)

Operating Instructions

Fcontrol

–

model series FXDM25/32AM

Diagnostics menu

L-BAL-E212-GB 1451 Index 003

Part.-No.

112/123

«
...
110
111
112
113
114
...
»

Содержание FXD32AM




























































































































Отзывы:

Нет отзывов

Похожие инструкции для FXD32AM

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 4

Бренд: ABB Страницы: 52

Бренд: Labelmate Страницы: 83

Бренд: Ricoh Страницы: 39

Бренд: GRASS Страницы: 19

Бренд: Johnson Controls Страницы: 4

Бренд: Anaheim Automation Страницы: 52

Presario V3000 - Notebook PC

Бренд: Compaq Страницы: 16

Бренд: Apricorn Страницы: 20

Бренд: KEBCO Страницы: 24

T5 AUTOSHORT BHz

Бренд: Simu Страницы: 28

Бренд: Qirod Страницы: 163

300979 - d2 16x DVD±RW FireWire HDD

Бренд: LaCie Страницы: 32

USB2.0CD-RW/DVD-ROM Combo Drive

Бренд: IBM Страницы: 72

Бренд: YASKAWA Страницы: 130

Бренд: Xinje Страницы: 23

Бренд: Danfoss Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды