ZIEHL-ABEGG FXD32AM Скачать руководство пользователя страница 58

Страница: 58 / 123

9.9.5

Limit

Controller Setup

After allocation of a digital input (

IO Setup) an adjustable limitation of the modulation

can be activated via a digital input (

“

”

“

”

, ..).

Display as long as no allocation has been carried out in

“

IO Setup

”

- - - -

The limitation in

ﬂ

uences both outputs in operation with two control circuits.

- - - - -

Limit

“

Limit value

”

= max. possible modulation (e.g.

speed reduction during night operation by
time switch).
Setting range:

“

Limit

”

“

n-max

”

up to

“

n-min

”

Factory setting: 100 %

max. modulation, i.

e. no limit.
Setting depending on device tye in: % or rpm.

50 %

100 %

Min.

L= 70% Min.= 0 % Max. = 100 %

50 %

0 %

100 %

L = 70% Min. = 35 % Max. = 85 %

25.03.2013

v_limit.vsd

Limit (idealized principle diagram)

Motor speed

Limit

Setpoint

Pband

Speed controller: setting signal

P-controller: control deviation

9.9.6

Minimum speed cut off

Controller Setup

This function is primarily signi

ﬁ

cant for installation of the device as a pure P Controller

in refrigeration and air-conditioning technology.
For operation mode speed controller

1.01

without function!

Display for operation with two control circuits:

“

1. Min. speed cut off

”

for control circuit 1

“

2. Min. speed cut off

”

for control circuit 2

OFF

Min. speed cut off

Msco = OFF

(factory setting)

If no

“

Min. speed

”

is adjusted, the fan stops with

reaching the desired value.
If

“

Min. speed

”

is adjusted (e.g. 20%), then no dis-

connection of the fan takes place. I.e., always a
minimum ventilation is ensured (fan does not go
under setting

“

Min. speed

”

Msco. e.g. -2.0 K

It takes place a disconnection from setting

“

Min.

speed

”

“

”

, if the given difference is reached re-

lated to the desired value.
At a plus value (+) before reaching the desired value
At a minus value (-) after falling below the desired
value.

50 %

100 %

Min.

Min. 35 %

Max. = 100 %

20 °C

7 K

27 °C

-2.0 K

10.05.2007

v_min_luft_abschalt.vsd

Minimum speed cut off (idealized principle diagram)

Motor speed

Setpoint

Pband

Actual value

Operating Instructions

Fcontrol

–

model series FXDM25/32AM

Programming

L-BAL-E212-GB 1451 Index 003

Part.-No.

58/123

Содержание FXD32AM




























































































































Результаты поиска

Содержание FXD32AM

Отзывы:

Похожие инструкции для FXD32AM

Бренды по названию

Популярные бренды

ZIEHL-ABEGG FXD32AM, Руководство по эксплуатации

Результаты поиска

Содержание FXD32AM

Отзывы:

Похожие инструкции для FXD32AM

Бренды по названию

Популярные бренды