ZIEHL-ABEGG FXD32AM Скачать руководство пользователя страница 47

Страница: 47 / 123

Setting

Min. Speed

(basic speed only when needed)

Setting range:

OFF

→

“

Shutdown Freq.

”

(

Motor Setup) -

“

Max. Speed

”

Factory setting:

OFF

OFF

Min. Speed

Setting

Max. Speed

(speed limitation only when needed)

Setting range:

“

Max. Frequency

”

(

Motor Setup) -

“

Min. Speed

”

Factory setting: 50.0 Hz

50.0 Hz

Max. Speed

Setting

Manual mode

“

OFF

”

= automatic control as function of the set parameters (Factory setting)

“

”

= automatic control without function, speed setting in menu

“

Speed manual

”

OFF

Manual mode

Setting

Speed Manual mode

Manual speed setting without in

ﬂ

uence by the external signal.

Activation by menu

“

Manual mode

”

or external contact at digital input (

IO Setup).

Setting range: 0...

“

Max. Frequency

”

(

Motor Setup)

Factory setting: 50.0 Hz
For information about deactivated regulation the adjusted value for manual speed is
indicated alternating with the actual value.

50.0 Hz

Speed man.

Additional menu item for mode

4.02

and

4.03

with outside-temperature dependent target-

setpoint.

Outside-temperature dependent target-setpoint

P-min.

-15 °C

T-min.

30 °C

T-Start

18.09.2014

v_pressure_set_dep_outtemp.vsd

[Pa]

T-Band

Setpoint1

Setpoint2

P-min.

Min. Setpoint

T-min

Min. temperature

T-Start

Setpoint reducing will start below this outside temperature

T-band

Temperature range

Outdoor temperature

An outside temperature compensation can be
activated (sensor connection

“

”

“

Analog In

”

) when being operated as a pressure regula-

tion device.
An optimal building climate, e.g., can be
achieved through this. Through this function,
the set and active

“

Setpoint1

”

“

Setpoint2

”

automatically changed proportional to the
measured outside temperature (

Info:

“

Set-

point control

”

Setting

T-Band SA

Temperature range in which the setpoint change continiously with outside temperature
Setting range: 0.0..100.0 K
Factory setting: 30.0 K

30 K

T-Band SA

Setting

T-Start SA

Setpoint reducing will start below this outside temperature
Setting range: -10.0...40.0

Factory setting: 15.0

T-Start SA

Operating Instructions

Fcontrol

–

model series FXDM25/32AM

Programming

L-BAL-E212-GB 1451 Index 003

Part.-No.

47/123

Содержание FXD32AM




























































































































Результаты поиска

Содержание FXD32AM

Отзывы:

Похожие инструкции для FXD32AM

Бренды по названию

Популярные бренды

ZIEHL-ABEGG FXD32AM, Руководство по эксплуатации

Результаты поиска

Содержание FXD32AM

Отзывы:

Похожие инструкции для FXD32AM

Бренды по названию

Популярные бренды