Zibro Kamin SRE 166 (Type B) Скачать руководство пользователя страница 66

Страница: 66 / 85

Refueling extension setting

TJ9

Existence

Not Existence

Item

Test Item

Specifications

Remarks.

Refueling extension setting Refueling extension setting can or cannot be used by TJ9.

O: With element, X: Without element

When refueling extension setting is enabled, the Main Circuit Board operates as follows:

- When extension button is pressed while a warning for refueling is given (during a

countdown in refueling), the Main Circuit Board stops controlling burning with the room

thermistor, forcibly changes to Med.-Low burning (P1), and extends time for refueling.

In addition, if Low burning setting is enabled, meeting the condition for Low burning

(3.3.3-7) allows Low burning (PL). If the condition for Save Mode flame extinguish is

met, the Main Circuit Board performs Save Mode flame extinguish.

- When refueling is extended, the Fuel Lamp will flash.

- To calculate extension time, multiply the number during refueling countdown by (X).

The value in parentheses depends on refueling extension time (the unit in sec. is

rounded off).

For example: When the setting of refueling extension time is 6 times:

If the refueling countdown is indicated as 10, extension time is 6 x 10=[60].

If the refueling countdown is indicated as 5, extension time is 6 x 5=[30].

- The warning buzzer for refueling turns on every two min. after the countdown reaches

to 10 min.

- The countdown during refueling extension is also counted during pre-heat.

- If refueling extension setting is enabled while burning is fixed, when extension button is

pressed, extension time for refueling is 6 times. However, burning remains at T13

timing, then changes to Med.-Low (or Low.) burning.

- During Save Mode flame extinguish, refueling countdown is not counted.

- To return to normal burning mode from refueling extension, either supply the heater

with kerosene so that the refueling sensor can be activated, or reset the Main Circuit

Board.

- Even while refueling is extended, the Main Circuit Board performs forced High burning.

- While refueling is extended, the Main Circuit Board cannot be set in burning lock mode.

- Refueling extension is disabled in the following cases:

During burning lock, during child lock, while a Fuel Lamp is off or flashing, during Save

Mode flame extinguish.

- Additional High burning timing (T39) is not counted while refueling is extended.

3.3.9-5

– 66 –

Содержание Kamin SRE 166 (Type B)






















































































Результаты поиска

Содержание Kamin SRE 166 (Type B)

Отзывы:

Бренды по названию

Популярные бренды

Zibro Kamin SRE 166 (Type B), Руководство по обслуживанию

Результаты поиска

Содержание Kamin SRE 166 (Type B)

Отзывы:

Бренды по названию

Популярные бренды