Zibro Kamin SRE 166 (Type B) Скачать руководство пользователя страница 64

Страница: 64 / 85

7 : 1

8 sec.

2 sec.

3 sec.

Fan Motor Post Purge Timing (T12)

Half-

wave

3 : 1

Fan Motor Post Purge Timing (T12)

Full-wave

Item

Test Item

Specifications

Remarks.

Min., DOWN Button

Hour, UP Button

Extension Button

(SRE 176)

Key-Lock (Childproof

Lock) Button

Save Mode Button

(except Oslo, SRE 701,

SRE 702 and SRE 703)

CIRCULATION FAN

MOTOR CONTROL

Fan motor half-wave

control setting

When temperature displays:

Press this button once to change temperature setting. If pressed within 10 sec.,

temperature decreases by one degree.

When current time and timer displayed:

Press this button once to change current time and timer. If pressed within 10 sec., clock

increases one min. Press this button more than one sec. to fast-forward the clock. If

time is not set when this button is pressed, the setting will become 0:00 (buzzer sounds

only once when this button is held down).

When temperature displays:

Press this button once to change temperature setting. If pressed within 10sec

temperature increases by one degree.

When current time and timer displayed:

Press this button once to change current time and timer. If pressed within 10 sec., clock

increases one hour. Press this button more than one sec. to fast-forward the clock. If

time is not set when this button is pressed, the setting will become 0:00 (buzzer sounds

only once when this button is held down).

When Refueling Remaining time displayed: Starts Fuelling Extension Operation (Refuel

Extension Operation. Please refer to 3.3.9-5)

When Error message displayed: Displays the time when the unit stopped by error.

Press this button more than 3 sec. starts the Key-Lock (Childproof Lock) operation.

During Key-Lock (Childproof Lock) operation, any buttons except Power Button (OFF)

and Key-Lock (Childproof Lock) Button does not work even if they are pressed. If the

operation is in Key-Lock (Childproof Lock) operation, press this button more than 3 sec.

releases Key-Lock (Childproof Lock) operation.

Press this button once changes to Save mode operation and press this button again

releases Save mode operation.

When Circulation Fan Motor half-wave control setting is enabled (3.3.9-3), fan motor

post-purge operates as follows:

However, if the Circulation Fan Motor stops due to an abnormality (except for stop for

refueling) and until initial state timing T8 ends, fan motor post-purge half-wave control

mentioned above will not be performed.

3.3.7-4

3.3.7-5

3.3.7-6

3.3.7-7

3.3.7-8

3.3.8

– 64 –

Additional High burning,

High, and Med.-High burning:

Med. burning:

Med.-Low and Low burning:

Full rotation

7:1 control

3:1 control

Содержание Kamin SRE 166 (Type B)






















































































Результаты поиска

Содержание Kamin SRE 166 (Type B)

Отзывы:

Бренды по названию

Популярные бренды

Zibro Kamin SRE 166 (Type B), Руководство по обслуживанию

Результаты поиска

Содержание Kamin SRE 166 (Type B)

Отзывы:

Бренды по названию

Популярные бренды