Zelmer JE 1003, Руководство пользователя

Страница: 58 / 62

62
JE1003-002_v01
Juice extractor safety operation instructions 4 Finally, disassemble the juice collector (2) from the
body (3) .
Wash the disassembled parts (except the motor
unit) carefully in hot water and wash-up liquid.
You can also clean them in a dishwasher in
max temp. 60°C (except for the strainer and the
motor unit). After drying them carefully, start
assembling the clean parts.
Preparation of the juice extractor for
operation (assembling)
1 Put the body of the juice collector (3) on the motor unit
so that a clamp (6) is placed slightly on the left of the buttons
on the motor and turn left to the limit (anticlockwise) so that
a clamp is placed over the buttons.
2
Put the juice container (2) on the body (3) so that the lip
(i) was placed in the cutting of the body (3) .
3 Put the filter (4) inside, press it slightly and check if it is
well mounted and rotates easily.
4 Put the lid (5) and close the clamps (6) .
5 Put the pusher (7) to the feeding tube.
6
Insert the pulp container (8) under the lid (5) in the
following way: lean the pulp container and place it under
a cover of the juice collector (3) and the lid (5) , and next push
it towards the motor (1) .
7 Place the juice collector under the lip (i) .
Place washed fruit and vegetables prepared for
juice extraction near the appliance.
Start-up of the juice extractor
and operation
1
Plug the juice extractor.
The appliance has an additional protection.
If it is plugged and the button power (a) is on
and if the switch is pulsating red, it means
that either the body (3) or the clamps (6) were
improperly placed on the lid. In such a situation
the appliance cannot be started. Check again
whether the assembly is proper until the lamp
(c) turns blue.
2 Press the button power (a) – the juice extractor will
operate on gear 1 and the control lamp will turn blue. It is
a gear recommended for fruit.
3 If you need operations on gear 2 (high rotation for hard
fruit like carrots, celeries, beetroots, apples, etc.), press (for
a short time, max. 2 sec.) the button (b) – the lamp (c) will
shine red with a continuous light. If it is necessary to return
to gear 1, press for a short time the button (b) and the juice
extractor will return to gear 1, the control lamp will shine blue
with a continuous light.
D
E
Danger! / Warning!
Risk of injury
Do not use the juice extractor if the spinning strainer
●
is damaged.
Make sure that the lid is clamped securely in place
●
before motor is turned on.
Do not take the pulp container out, nor release the
●
locks (clamps), when the juice extractor is working.
Use the pusher only to push food into the feeder
●
opening.
Do not use the juice extractor without pulp collector.
●
Warning!
Risk of property damage
Immediately turn off the juice extractor if you notice
●
strong vibrations or the rotation speed is reduced.
Clear the strainer and its cover.
Turn the motor off and unplug the appliance if food
●
is blocked in the feeder opening or on the grinding
blades. Remove the cause of blocking.
Do not overload the appliance with extensive amount
●
of product or do not push it to strong (with a pusher),
because a sudden increase of juice amount in the bowl
spout can cause the juice overflow out of the lid or into
pulp collector.
Tip
Product information and tips on its use
Use a soft bristle brush to clean the strainer with the
●
sharp grinding blades.
Preparation of the juice extractor for
operation (disassembling)
Before using the juice extractor for the first
time, disassemble it and wash parts in contact
with the processed product.
Place the juice extractor near the socket on the firm,
●
clean and dry surface.
1
Pull down the clamps (6) so that the tracks moved out of
grooves of the lid (5) .
2 Take the pusher (7) and the lid (5) out.
3
Then remove the juice collector (2) including the body
(3) and the filter (4) . To this end, turn the body (3) right
(clockwise) to the limit and raise the body with the juice
collector and the filter.
C