Zapi COMBIACX, Руководство пользователя

Страница: 62 / 81

Page - 62/81 AFCZP0BC- COMBIACX & ACEX - User Manual
12.2 Alarms overview
Error Code Description Effect
Machine status
when the test is
done
Restart
procedure
Capacitor
charge - MDI
CAN 60 Power capacitors voltage does not increase Valve, pump, traction
stopped, Lc opened, Eb
applied start-up Valve or pump or
traction request
Vmn low - MDI
CAN 72 Motor output voltage lower than expected Valve, pump, traction
stopped, Lc opened, Eb
applied start-up, traction Valve or pump or
traction request
Vmn high -
MDI CAN 31 Motor output voltage higher than expected Valve, pump, traction
stopped, Lc opened, Eb
applied start-up, traction Valve or pump or
traction request
Power mos
short - MDI
CAN 88 Short circuit on the power mosfets Valve, pump, traction
stopped, Lc opened, Eb
applied start-up Valve or pump or
traction request
Coil short. MC-
EB - MDI CAN
76 Shortcircuit on LC or EB coil Valve, pump, traction
stopped, Lc opened, Eb
applied stby, traction Valve or pump or
traction request
Driver shorted -
MDI CAN 74 Driver of LC coil is shorted, so it is not able to open
the LC, or LC coil is disconnected Valve, pump, traction
stopped, Lc opened, Eb
applied start-up Valve or pump or
traction request
Contactor
Driver - MDI
CAN 75 Driver of LC coil is damaged (not able to close) Valve, pump, traction
stopped, Lc opened, Eb
applied stby, traction Valve or pump or
traction request
Contactor
Open - MDI
CAN 77 The LC coil has been driven but LC does not close Valve, pump, traction
stopped, Lc opened, Eb
applied stby, traction Valve or pump or
traction request
Contactor
closed - MDI
CAN 75 LC contact is stuck Valve, pump, traction
stopped, Lc opened, Eb
applied start-up Valve or pump or
traction request
Aux driv. Shrt. -
MDI CAN 40 When the mos of EB is shorted Valve, pump, traction
stopped, Lc opened, Eb
applied start-up,stby,marcia Valve or pump or
traction request
Aux driver
open - MDI
CAN 42 Driver of EB coil is damaged (not able to close) Valve, pump, traction
stopped, Lc opened, Eb
applied stby, traction Valve or pump or
traction request
Pos. EB
shorted - MDI
CAN 86 Output of built in Smart Driver, which supplies Eb coil
positive, is high (= +batt) when the tiller switch is
opened. Valve, pump, traction
stopped, Lc opened, Eb
applied start-up Valve or pump or
traction request
Logic Failure
#1 - MDI CAN
54 Overvoltage/Undervoltage condition has been
detected Valve, pump, traction
stopped, Lc opened, Eb
applied start-up Valve or pump or
traction request
Logic Failure
#2 - MDI CAN
55 Motor voltage feedback circuits are damaged Valve, pump, traction
stopped, Lc opened, Eb
applied stby, immediately
after Lc closing Valve or pump or
traction request
Logic failure
#3 - MDI CAN
17 Failure in the high current HW protection circuit valve, pump, traction
stopped, Lc opened, Eb
applied start-up, stby Valve or pump or
traction request
Stby i high -
MDI CAN 53 In stby condition (no current applied to the traction
motor) the current feedbacks are aout of permitted
stby range Valve, pump, traction
stopped, Lc opened, Eb
applied start-up, stby Valve or pump or
traction request
Wrong Battery -
MDI CAN 41 The battery voltage is too low or too high (< 0,8 Vbatt
OR > 1,2 Vbatt) Valve, pump, traction
stopped, Lc opened, Eb
applied start-up, stand-by
(only immediately
after Lc closing) Valve or pump or
traction request
Analog input -
MDI CAN 96 Problem on the A/D conversion of uC Valve, pump, traction
stopped, Lc opened, Eb
applied traction Valve or pump or
traction request
Encoder Error -
MDI CAN 82 Problem on the encoder Valve, pump, traction
stopped, Lc opened, Eb
applied traction Valve or pump or
traction request
Tiller error -
MDI CAN 64 Input mismatch between hard&soft switch input and
tiller input Traction stopped, Eb applied start-up, stby,
traction
Valve or pump or
traction request
Watchdog -
MDI CAN 08 One of two (or both) Watchdog circuit outputs
becomes high due to an HW or SW problem Valve, pump, traction
stopped, Lc opened, Eb
applied start-up, stby,
traction Key re-cycle