Yuchai U35 Скачать руководство пользователя

Страница: 2 / 157

Warning

Improper operation of the machine may cause injury or death. The
following shall be done before using the machine:

⚫

Keep in mind the safety regulations and correct usage specifications
of the machine.

⚫

Read and understand the relevant description of the instruction on
safe operation of the machine.

⚫

Understand and be familiar with all safety markings on the machine.

⚫

Keep the irrelevant personnel be away from the working area.

⚫

Before formally operating the machine in the working area, the safety
operation training of the machine shall be carried out in advance.

You are responsible for complying with relevant laws and regulations
and the instructions of Yuchai Heavy Industry on machine operation and
maintenance.

is the registered trademark of Guangxi Yuchai Heavy Industry Co., Ltd. in China.

Содержание U35






























































































































































Результаты поиска

Содержание U35

Отзывы:

Похожие инструкции для U35

Бренды по названию

Популярные бренды

Yuchai U35, Руководство оператора

Результаты поиска

Содержание U35

Отзывы:

Похожие инструкции для U35

Бренды по названию

Популярные бренды