Yuchai U35 Скачать руководство пользователя

Страница: 102 / 157

4-33

Fault

Causes

Solutions

19. Abnormal
traveling

• The track is too tight or loose

• Re-adjust

• Reduced oil pump
performance

• Consult with dealers of the
manufacturer

• Crawler frame distorted

• Repair or replace

• Crushed stones or rocks in the
track chain

• Take the stone out and repair

• Oil leakage of the control valve

• Consult with dealers of the
manufacturer

• Reduced motor performance

• Consult with dealers of the
manufacturer

20. Abnormal
slewing

• Reduced oil pump
performance

• Consult with dealers of the
manufacturer

• Slewing motor damaged

• Consult with dealers of the
manufacturer

• Pilot valve out of work

• Consult with dealers of the
manufacturer

21.
Discontinuous
slewing

• Worn slewing gear

• Consult with dealers of the
manufacturer

• Slewing bearing or ball bearing
damaged

• Consult with dealers of the
manufacturer

• Lack of grease

• Consult with dealers of the
manufacturer

• Oil leakage of the control valve

• Consult with dealers of the
manufacturer

22. Air
conditioning
system noise

• Loose electrical connectors
causing abnormal clutch noise

• Insert the connector securely or
repair as necessary

• Loose belt

• Tighten appropriately, replace if
damaged

• Loose blower blades

• Reassemble securely

• The blower does not work
normally

• Repair or replace

• The fan does not work
normally

• Repair or replace

• Damaged compressor bearing

• Replace

• Damaged tensioner bearing

• Replace

23. Air
conditioner
cooling does
not work

• Electrical circuit failure

• Repair or replace

• Air conditioning switch failure

• Repair or replace

• No refrigerant

• Check for leakage, repair, and
refill refrigerant

• System blockage

• Clean or replace

• Belt loose or broken

• Adjust or replace

• Expansion valve failure

• Clean or replace

• The compressor operates
abnormally

• Repair or replace

• Pressure switch failure

• Replace

24. Unsteady
cooled air

• Poor circuit contact

• Maintenance

• Loose belt

• Adjust the belt tension

• Improper adjustment of air

• Re-adjust

Содержание U35






























































































































































Результаты поиска

Содержание U35

Отзывы:

Похожие инструкции для U35

Бренды по названию

Популярные бренды

Yuchai U35, Руководство оператора

Результаты поиска

Содержание U35

Отзывы:

Похожие инструкции для U35

Бренды по названию

Популярные бренды