Yosin EVM1001, Инструкция по установке и программированию

Страница: 10 / 17

) ($% *!
SYS _2 1_ [XX ]
Waiting time for caller to dial numbers after Greeting/ Busy/ No-answer prompt. (Default=03 sec.)
SYS _2 2_ [XX ] Waiting time for the operator answering during working hours (Default =20 sec.)
SYS _2 3_ [XX ] Waiting time for the operator answering during closing hours (Default =20 sec.)
SYS _2 4_ [XX ] Waiting time for the extension answering during working hours (Default =20 sec.)
SYS _2 5_ [XX ] Waiting time for the extension answering during closing hours (Default =20 sec.)
•
XX=00 means Unsupervised Transfer
•
If Unsupervised Transfer is set, you can set
Function Code of Call Pickup to retrieve the
unanswered call or set ID Code for "No-
answer" prompt.
SYS _2 7_ [XX ]
Waiting time for Call Pickup (Default = 20 seconds). The waiting time should be short and shorter than the Ringing time set by
PABX to prevent Pickup calls by mistakes.
SYS _3 1_ [X]
Number of rings to wait before the EVM answers incoming calls.
(' *
SYS _4 1_ [X] X: 1=Number Repeat (Default) 2=No If X=1, then EVM will announce "extension number" and "please wait" before transferring
SYS _4 3_ [X] X: 1=Raise the volume of greeting messages 2=No(Default)
SYS _4 7_ [X] X: 1=Ext. Port auto detection 2=No(Default) If you know PABX may lockout the EVM Ext. Port , please set X=1
SYS _4 0_ [X] X: 1= Silent compression(Default) 2= No silent compression
SYS _6 8_ [
XXXX
]
System Program Password (Default = 0 0 )
SYS _6 9_ [
XXXX
]
Administrator Program Password(Default = none); The first 2 digits can not be the same as System Program Password
SYS _8 Report of remained voice message capacity; Program Prompt: "8""Beep""XXXX(seconds)"
SYS _9 Report the version of EVM. Program Prompt: "XXXXXXXX"
SYS _0 Wait for 2 seconds to enter Administrator Program. Program Prompt: “Welcome to Administrator Program”
' )( ** ( +
•
Please refer to the operation instruction of PABX extension.
SYS_52_[X] EVM releases after call answered (Default=5)
SYS_53_[X] EVM releases for Unsupervised Transfer(Default=5)
SYS_54_[X] Retrieving call when Error Tone(Default=1)
SYS_55_[X] Retrieving call when Busy Tone(Default=1)
SYS_56_[X] Retrieving call when No-answer(Default=1)
SYS_59_[X] For Call Pickup (Default=8)
If Function Code of Call Pickup and Unsupervised Transfer were set,
EVM will retrieve the unanswered call with the operating way
SYS_59_[X] after waiting time for Call Pickup is over.
# Operating way:
1= HOOK-FLASH
2= HOOK-FLASH + Function Code
3= HOOK-FLASH twice
4=
HOOK-FLASH
and then
ON
& OFF
HOOK
5= ON
& OFF
HOOK
6= ON
& OFF
HOOK + Function Code
7= ON
& OFF
HOOK
and then
HOOK-FLASH
8= Function Code + Extn
9= Extn + Function Code
0= Defined by ADM_59930_[X…]
= Defined by ADM_59933_[X…]
SYS_61_[X…] Function Code of call transferring (Default =none)
SYS_62_[X…] Function Code of Retrieving calls (Default =none)
ADM_59907_[X…] Function Code of Call Pickup (Default =none)
ADM_59931_[X…] The 1 st Function Code of ADM_59930_[X…] (Default =none)
ADM_59932_[X…] The 2 nd Function Code of ADM_59930_[X…] (Default =none)
ADM_59934_[X…] The 1 st Function Code of ADM_59933_[X…] (Default =none)
ADM_59935_[X…] The 2
nd
Function Code of ADM_59933_[X…] (Default =none)
#
If X… less than 4 digits, please press # sign to
complete the digit entering. 0000 means to delete.
#
For special character: - enter
- enter 1
A
- enter 2
B
- enter 3
C
- enter 4
ADM_59930_[X…] Sequence of operating way (Default =none)
ADM_59933_[X…] Sequence of operating way (Default =none)
#
If X… less than 4 digits, please press # sign to
complete the digit entering. 0000 means to delete.
#
X… is the sequence of operating way
0=On & Off Hook 1=HOOK-FLASH 2=Extn
3= 1
st Function Code 4=2 nd Function Code