York EX Series страница 130 Скачать руководство пользователя

Страница: 130 / 176

JOHNSON CONTROLS

130

FORM 155.32-ICOM1.EN.GB

ISSUE DATE: 10/13/2017

SECTION 7 – MAINTENANCE

START THE CHILLER-HEATER AFTER IT HAS

BEEN STOPPED FOR A LONG PERIOD

When starting the chiller-heater after stopping it for a

long period, check it according to the following pro-

cedure.

Checks Before Operation Starts

1. Check the insulation of the Control Center and

electric system.

2. Check the operation of the Control Center and

safety devices.

3. Check that the refrigerant blow valve V8 is closed.
4. Check the vacuum level in the machine. Use pres-

sure gauge of the high-temperature generator.

It should be less than -0.1 MPaG.

5. Check the fuel gas supply.
6. Press the Refrigerant Pump

Stop

button on the

Setting screen.

If the checks show no problems, start the chiller-heater.

CHECKS AFTER OPERATION STARTS

1. 10-15 minutes after the chiller-heater and the so-

lution pump start, check the level gauge of the re-

frigerant tank.

2. If the refrigerant level is within the level gauge,

press the Refrigerant Pump

Auto

button.

3. Observe the operation for a while. Check that the

refrigerant liquid level does not drop.

4. Use the procedure shown in

Purge Procedure on

page 130

, to purge air from the low pressure side

(absorber).

Remember: Only deionized water may

be used as the refrigerant in the chiller-

heater

PURGE PROCEDURE

Air must be purged from the chiller-heater to maintain

its performance and prevent deterioration of its internal

parts. This chiller-heater has an automatic purge sys-

tem.
Even if the automatic purge mode is used during nor-

mal operation, perform the manual operation for the

purging tank and absorber periodically. For the purging

period, see

Table 28 on page 129

CAPACITY CHECK METHOD OF VACUUM

PUMP

For commissioning and regular maintenance, check

the capacity of the vacuum pump first according to the

following procedure.

1. Check the oil level in the vacuum pump.
2. If the oil is cloudy, it contains water and must be

replaced with new oil.

See the Operation Manual for the Vacuum

Pump for more information on how to

change the oil.

3. Open the gas ballast (remove the plug).

If the purge unit is operated with the

gas ballast closed, water is left in the oil.

The oil will need to be replaced more

frequently.

4. Set the valves according to pattern A. See

Figure

59 on page 141

and

Table 27 on page 127

5. Press the Purge Model

Manual

button on the Set-

ting screen.

6. Press the Manual Purge

button. The vacuum

pump starts. The solenoid valves SV1 and SV2

open.

After another 1-2 minutes, confirm that the vacu

um gauge stands at 0 - approximately 1 kPa.

8. Press the Manual Purge

OFF

button. The vacuum

pump stops.

9. Wait for 30 minutes..

10.

Confirm that the vacuum down is within 2 kPa.

Содержание EX Series

















































































































































































Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды

York EX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды