York EX Series страница 105 Скачать руководство пользователя

Страница: 105 / 176

JOHNSON CONTROLS

105

SECTION 6 – OPERATION

FORM 155.32-ICOM1.EN.GB

ISSUE DATE: 10/13/2017

FAILURE HISTORY SCREEN

FIGURE 39 -

FAILURE HISTORY SCREEN

LD20941

You move to the Failure History screen after you press

the

Failure

button in the History Menu screen section.

The Failure History screen shows failure information

for the last failure and up to six previous failures. The

Failure section contains the following fields of infor-

mation:

Failure Name:

name or type of failure

Measured Date and Time:

date and time of the failure

Operation:

operation status of the chiller-heater

Operation Method:

selected operation method

Solution Pump:

operation status of the solution pump

Refrigerant Pump:

operation status of the refrigerant

pump

Burner Fan:

operation status of the burner fan

Combustion:

status of the combustion (ON or OFF)

Operation Hours:

total operation hours

Operation Freq.:

how many times the chiller-heater

has started using the

OPER.

button or a remote start

signal

Failure Frequency:

how many times the chiller-heater

has had a failure alarm

Alarm Frequency:

how many times an alarm has been

triggered for the chiller-heater

Auto Purge Frequency:

how many times an automat-

ic purge has been performed
The Chilled/Hot water section of the screen shows you

the following information:

Inlet Temperature:

temperature of the chilled/hot wa-

ter measured as it enters the evaporator

Outlet Temp.:

temperature of the chilled/hot water

measured as it leaves the evaporator.
The Cooling Water section shows you:

Inlet Temperature:

temperature of the cooling

water measured as it enters the absorber.

Содержание EX Series

















































































































































































Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды

York EX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды