York EX Series страница 155 Скачать руководство пользователя

Страница: 155 / 176

JOHNSON CONTROLS

155

SECTION 7 – MAINTENANCE

FORM 155.32-ICOM1.EN.GB

ISSUE DATE: 10/13/2017

PRECAUTIONS AGAINST EXTERNAL

DAMAGE

Avoid storing the machine in a place that is easily ac-

cessible or near a construction site. If this is unavoid-

able, provide the machine with protection.
If it is not possible to protect the machine, fill the in-

terior with N2 to minimize the amount of air leakage.

For details, contact your local Johnson Controls ser-

vice center.

The wet storage procedure is as follows if either chilled/

hot line or the cooling water line is an open system:

1. Completely drain the water from the systems if it

has deteriorated in quality.

2. Clean the water systems by passing clear water

through them from a position higher than the

chiller-heater.

3. Fill the water systems with clear water.
4. Circulate the clear water through the water pump

for 30 minutes to one hour to clean it.

5. Drain the water.
6. Completely fill the water systems with clear water

again.

7. Store the machine.

DRY STORAGE METHOD

The dry storage method should be used if the chilled/

hot water system or the cooling water system may

freeze in the winter or, if the water system has a lining

tube. Do not simply drain the chilled/hot, and the cool-

ing water and store the machine. This significantly in-

creases the possibility of corrosion of the heat transfer

tube and rust. For details, see

Table 33 on page 153

The dry storage procedure is as follows if either the

chilled/hot line or the cooling water line is an open sys-

tem:

1. Completely drain the water.
2. Clean the water systems by passing clear water

through them from a position higher than the

chiller-heater.

3. Fill the water systems with clear water.
4. Circulate the clear water through the water pump

for 30 minutes to one hour to clean it.

5. Drain the water from each waterbox.
6. Dry the interior of each waterbox and the heat

transfer tube.

7. Store the machine.

Содержание EX Series

















































































































































































Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды

York EX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды