York EX Series страница 158 Скачать руководство пользователя

Страница: 158 / 176

JOHNSON CONTROLS

158

FORM 155.32-ICOM1.EN.GB

ISSUE DATE: 10/13/2017

SECTION 7 – MAINTENANCE

LD20942

Cooling

Tower

Open/close signal for three way valve

Start/stop signal for cooling tower fan

Strainer

Thermometer

Drain valve

Thermometer

Cooling water pump

Close

Open slightly

Filled with water

Drain valve

Close

Chiller-Heater

FIGURE 61 -

WET STORAGE DURING HEATING OPERATION PERIOD

Work Procedure

1. If the quality of the remaining cooling water is

deteriorated, drain all the cooling water from the

absorber and the Condenser.

2. Flow clean water from a higher location than the

chiller-heater. Then feed the clean water continu-

ously and clean the tubes well.

3. Fill the absorber and the condenser with clean wa-

ter.

4. Circulate the clean water with the cooling water

pump for 30 min. to 1 hour.

5. Drain all of the cooling water from the Absorber

and Condenser.

6. Fill the absorber and condenser with clean water.
7. Keep this condition during heating operation pe-

riod.

Dry Storage

Dry storage involves draining the water from the tubes.

It most often used when the unit is installed in an out-

door location.
. Condition around the chiller-heater:

•

During the heating operation period, there is con-

cern of cooling water freezing.

•

Cooling tower is installed at the same level

(height) of the chiller-heater.

•

Lining pipe is used for the cooling water piping

system.

Do NOT leave the tubes in absorber and

condenser as is after simply draining the

remained cooling water. If you do, the heat

transfer tubes will be at high risk of corro-

sion and rusty water (red rust) generation.

Содержание EX Series

















































































































































































Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды

York EX Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание EX Series

Отзывы:

Похожие инструкции для EX Series

Бренды по названию

Популярные бренды