YOKOGAWA WT200, Руководство пользователя

Страница: 204 / 242

14-42
IM 253421-01E
Overview of Registers and Queues
Name Function Writing Reading
Status byte — Serial poll (RQS),
*STB? (MSS)
Service request Masks status byte. *SRE *SRE?
enable register
Standard event Event in the — *ESR?
register instrument (1)
Standard event Masks standard *ESE *ESE?
enable register event register.
Extended event Event in the —
STATus:EESR?
register instrument (2)
Extended event Masks extended STATus:EESE STATus:EESE?
enable register event register.
Condition Current instrument — STATus:CONDition?
register status
Transition Extended event STATus:FILTer STATus:FILTer
filter occurrence conditions
<x> <x>
Output queue Stores response All executable queues
message to a query.
Error queue Stores error Nos. — STATus:ERRor?
and messages.
Registers and Queues which Affect the Status Byte
Registers which affect each bit of the status byte are
shown below.
Standard event register: Sets bit 5 (ESB) of status byte to “1” or “0”.
Output queue: Sets bit 4 (MAV) of status byte to “1” or “0”.
Extended event register: Sets bit 3 (EES) of status byte to “1” or “0”.
Error queue: Sets bit 2 (EAV) of status byte to “1” or “0”.
Enable Registers
Registers which mask a bit so that the bit does not
affect the status byte, even if the bit is set to “ 1 ”, are
shown below.
Status byte: Masks bits using the service request enable register.
Standard event register: Masks bits using the standard event enable register.
Extended event register: Masks bits using the extended event enable register.
Writing/Reading from Registers
The *ESE command is used to set bits in the standard
event enable register to “
1
” or “
0
”, and the
*ESR?
query
is used to check whether bits in that register are set to
“ 1 ” or “ 0 ”. For details of these commands, see section
14.3.
14.4.2 Status Byte
Overview of Status Byte
7 6 ESB MAV EES EAV 1 0
RQS
MSS
Bits 0, 1 and 7
Not used (always “
0
”)
Bit 2 EAV (Error Available)
Set to “ 1 ” when the error queue is not empty, i.e. when
an error occurs. For details, see page 14-45.
Bit 3 EES (Extended Event Summary Bit)
Set to “ 1 ” when a logical AND of the extended event
register and the corresponding enable register is “
1
”,
i.e. when an event takes place in the instrument. See
page 14-44.
Bit 4 MAV (Message Available)
Set to “
1
” when the output queue is not empty, i.e.
when there is data which is to be output when an
inquiry is made. See page 14-45.
Bit 5 ESB (Event Summary Bit)
Set to “ 1 ” when a logical AND of the standard event
register and the corresponding enable register is “ 1 ”,
i.e. when an event takes place in the instrument. See
page 14-43.
Bit 6 RQS (Request Status)/MSS (Master Summary
Status )
MSS is set to “ 1 ” when a logical AND of the status byte
(except for bit 6) and the service request enable
register is not “ 0 ”, i.e. when the instrument is
requesting service from the controller.
RQS is set to “ 1 ” when MSS changes from “ 0 ” to “ 1 ”,
and is cleared when a serial poll is performed or when
MSS changes to “ 0 ”.
Bit Masking
To mask a bit in the status byte so that it does not
cause an SRQ, set the corresponding bit of the service
request enable register to “
0
”.
For example, to mask bit 2 (EAV) so that no service
will be requested, even if an error occurs, set bit 2 of
the service request enable register to “ 0 ”. This can be
done using the
*SRE
command. To query whether
each bit of the service request enable register is “ 1 ” or
“ 0 ”, use *SRE? . For details of the *SRE command, see
section 14.3.
14.4 Status Report