YOKOGAWA TC10, Инструкция по эксплуатации

Страница: 7 / 36

Yokogawa Electric Corporation - TC10 - ENGINEERING MANUAL - PAG. 7
4. Using and buttons set the code 1 value
according to the following tables.
L M N O
Prepare your code 1
Input Type and Range L M
TC J -50 to +1000°C 0 0
TC K -50 to +1370°C 0 1
TC S -50 to 1760°C 0 2
TC R -50 to +1760°C 0 3
TC T -70 to +400°C 0 4
PT 100 -200 to +850°C 0 7
PT 1000 -200 to +850°C 0 8
Linear 0 to 60 mV 0 9
Linear 12 to 60 mV 1 0
Linear 0 to 20 mA (this selection forces Out 4 = TX) 1 1
Linear 4 to 20 mA (this selection forces Out 4 = TX) 1 2
Linear 0 to 5 V 1 3
Linear 1 to 5 V 1 4
Linear 0 to 10 V 1 5
Linear 2 to 10 V 1 6
TC J -58 to +1832°F 1 7
TC K -58 to +2498°F 1 8
TC S -58 to 3200°F 1 9
TC R -58 to +3200°F 2 0
TC T -94 to +752°F 2 1
PT 100 -328 to +1562°F 2 4
PT 1000 -328 to +1562°F 2 5
L M N O
c%d1
:
Control mode OP1 OP2 OP3 OP4 N O
ON/OFF heating = H
H AL1 AL2 AL3
0 0
NU AL1 AL2 H
0 1
ON/OFF cooling = C
C AL1 AL2 AL3
0 2
NU AL1 AL2 C
0 3
ON/OFF with neutral
zone (H/C)
H C AL2 AL3
0 4
H AL1 AL2 C
0 5
C H AL2 AL3
0 6
NU H AL2 C
0 7
C AL1 AL2 H
0 8
NU C AL2 H
0 9
PID heating = H
H AL1 AL2 AL3
1 0
NU AL1 AL2 H
1 1
PID cooling = C
C AL1 AL2 AL3
1 2
NU AL1 AL2 C
1 3
PID double action (H/C)
H C AL2 AL3
1 4
H AL1 AL2 C
1 5
C H AL2 AL3
1 6
NU H AL2 C
1 7
C AL1 AL2 H
1 8
NU C AL2 H
1 9
5. Push the button.
The upper display shows
cod2
flashing while the lower
display shows
0000
or the
cod2
value stored in memory.
6.
Using and buttons set the code 2 value
according to the following tables.
P Q R S
Prepare your code 2
Alarm 3
R
Alarm 2
Q
Alarm 1 P
Not used
0 0 0
Sensor break 1 1 1
Absolute
High 2 2 2
Low
3 3 3
Absolute High/Low
External High/Low
4 4 4
Internal High/Low
5 5 5
Deviation
Deviation high
6 6 6
Deviation low
7 7 7
Band
External band
8 8 8
Internal band 9 9 9
P Q R S c%d2
:
Auxiliary functions activation
S
None 0
Wattmeter (instantaneous power expressed in W) 1
Wattmeter (energy expressed in Wh) 2
Absolute worked time (expressed in days) 3
Absolute worked time (expressed in hours)
4
7. Push the button.
If the just entered codes are accepted, the upper display
shows
code
while the lower display shows
good
.
8.
Push the button to save the configuration code and
exit the Code configuration procedure.
Note: After using the “ Code configuration ” method, it will
always be possible to modify the parameters using the
“
Complete configuration ” method. If the value of a
parameter among those included in the configuration
codes (
cod1
-
cod2
) gets modified, the instrument
will acquire the change while maintaining all the other
parameters.
WARNING! After a parameter change made as described
in the previous “Note”, when retrieving the
configuration codes (
cod1
-
cod2
), the lower
display will show “
oFF
” to alert the operator that
one of the parameters has been changed.