background image

23

IM 04L55B01-02EN

 

3.  Make that the source voltage is within the maximum rated 

voltage range of the provided power cord. Then, connect 

the other end of the cord to the outlet. Use a grounded 

three-prong outlet.

Precautions to Be Taken While Wiring the Power 

Supply (Power Supply Suffix Code: 2)

Make sure to follow the warnings below when wiring the 

power supply. Failure to do so may cause electric shock or 

damage to the instrument.

●  Wire the power cable to the power supply terminal, 

making sure that the polarity is correct.

●  Connect the power cables after checking that the 

power switch of the GM90PS is turned OFF.

●  Using other wires may cause abnormal heating or fire.

Wiring Procedure

1.  Turn off the GM90PS power supply, and then remove the 

transparent power supply terminal cover.

2.  Wire the power cable to the power supply terminal, making 

sure that the polarity is correct. 

Use ring-tongue crimp-on lugs (for M4 screws) with 

insulation sleeves. The recommended torque for tightening 

the screws is 1.4 to 1.5 N•m.

 

+

3.  Attach the transparent power supply terminal cover, and 

fasten it with screws.

Turning the Power On and Off

If the power switch of GM/GX60 systems under 

operation be turned on or off carelessly, it may result 

the system down or injury.

Check the following points before turning on the power 

switch.

●  The power cord or wires are connected properly.

●  The GM is connected to the correct power supply.

If the input wiring is connected in parallel with another 

instrument, do not turn on or off the GM or other 

instrument during operation. If you do, measured values 

may be affected.

Check the following points before turning off the power 

switch.

●  The GM10 is not accessing the external storage me

-

dium.

  You can turn the power on and off using the power switch 

on the front panel of the GM90PS.

  A self-test takes place for a few seconds, and then the GM 

will be running.

 

Power switch

Connecting GX90EX Expansion Modules

The GX90EX is used to configure a multi unit system.

•  For the main unit, link the GX90EX to the left end as seen 

from the front of the unit.

•  For a sub unit, link it next to the GM90PS.

Connect the GX90EXs of the main unit and sub units with 

Ethernet STP (shielded) cables. Only cascaded connection is 

supported.

Configuring the GX90EX Expansion Modules

Before setting the GX90EX dipswitches, turn off the unit.

 

Port

Setting switches (dipswitches)

System status LED

EXBus status LED

7 segment LED

Содержание SMARTDAC+ GM10

























Отзывы: