YOKOGAWA CM6G Скачать руководство пользователя страница 27

Страница: 27 / 65

<3.Construction and Function>

3-2

IM 11R02A01-02E

5th Edition : Dec. 28, 2016-00

Town Gas Use

The sample gas, introduced through line filter (3-1), increases its pressure by pump, or

decreases by pressure reducing valves, according to the pressure at the sampling point. The

pressure gauge (3-2) indicates 8 to 18 kPa and the flowmeter (3-3) approx. 10 l/min, respectively.

The sample gas, then, is set its differential pressure to 500 Pa by pressure reducing valve (3-4)

and (3-6), and at this time the pressure gauge (3-5) indicates approx. 3 kPa. When the density

compensation system is equipped, the sample gas is introduced to the density meter with the flow

rate of 1 l/min, through the flowmeter (5-3).
The standard gas is reduced its pressure to 8 to 18 kPa by the pressure reducing valve (4-1), and

supplied, same as the sample gas, with the flow rate approx. 10 l/min.

Steel Mill Use

The pressure of the sample gas is increased, by the pump, according to that of the sampling

point.

The pressure gauge (3-1) indicates approx. 6 kPa. The sample gas then flows through the

washing bubbler (3-2) and the fulflo filter (3-3), and then secure a constant pressure in the

pressure regulating pot (3-4) through the water sealed pipe from the dehumidifier (3-5), then set

the differential pressure by the pressure reducing valve (3-6) to 500 Pa.

To increase the pressure by the pump, a drain pot (3-9) is added. When the density

compensation system is equipped, the sample gas is supplied to the density meter with its flow

rate of 1 l/min, through the flowmeter (5-3). The pressure of the standard gas is reduced by the

pressure reducing valve (4-1) to about 6 kPa and is supplied by the flowmeter (4-2) with the flow

rate about 10 l/min.

Standard Flow Sheet

1. Town Gas Application (Standard Type)

V-3

V-2

V-1

V-4

3-1

V-5

V-12

1-6

7-2

7-1

6-2

6-1

4-1

INST.AIR IN

0.3~0.7MPa

50Nl/min

SAMPLE GAS IN

STD GAS IN (ZERO)

SAMPLE GAS OUT

OR VENT

V-6

V-11

V-7

V-13

V-14

V-9

V-10

V-8

V-16

V-15

5-3

3-4

3-6

3-3

3-2

3-5

1-4

1-5

GAS

DP.T

AIR

DP.T

1-3

1-2

1-1

2-4

2-3

2-1

2-5

2-2

3-7

No. Item
1-1 Calorie detector

1-2 Solenoid valve

1-3 Orifice assembly

1-4 Differential pressure transmitter (air)

1-5 Differential pressure transmitter (gas)

1-6 Computing station

2-1 Air set

2-2 Pressure reducing valve

2-3 Pressure gauge

2-4 Preheating chamber

2-5 One touch coupler

No. Item
3-1 Line filter

3-2 Pressure gauge

3-3 Flowmeter

3-4 Pressure reducing valve

3-5 Pressure gauge

3-6 Pressure reducing valve

3-7 Diaphragm pump (when specified)

3-8 Pressure reducing valve (when specified)

4-1 Pressure reducing valve for standard gas

No. Item

5-1 Density meter detector (when specified)

5-2 Density meter converter (when specified)

5-3 Flowmeter for density meter (when specified)

6-1 Zero gas (supplied by customer)

6-2 Span gas (supplied by customer)

7-1 Pressure reducing valve for cylinder (optional)

7-2 Pressure reducing valve for cylinder (optional)

V1...16 Ball valve, needle valve

3-8

*1: CM6G-S6



10 (with density meter)

*2: CM6G-S63



0 (with diaphragm pump)

*3: CM6G-S64



0 (with pressure reducing valve)

CM6G-S6200, S6210, S6300, S6310, S6400, S6410

5-2

5-1

Maximum back pressure

is 1.5 kPa and no pressure

fluctuation is allowed.

FLOW-6410.ai

STD GAS IN (SPAN)

Figure 3.2 Flow Sheet (for Town Gas)

Содержание CM6G


































































Результаты поиска

Содержание CM6G

Отзывы:

Похожие инструкции для CM6G

Бренды по названию

Популярные бренды

YOKOGAWA CM6G, Руководство пользователя

Результаты поиска

Содержание CM6G

Отзывы:

Похожие инструкции для CM6G

Бренды по названию

Популярные бренды