YOKOGAWA CM6G Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 65

background image

<7. Maintenance>

7-2

IM 11R02A01-02E

5th Edition : Dec. 28, 2016-00

7.2 Regular Check

Refer to Figure 3.2 , 3.3 and 3.4. The flow sheet depends on the specification.

7.2.1

Cleaning of the Orifice Plate and Replacement of

O-ring

When something like dust adhere to the orifice holes, the output declines.

Follow the instruction as below to clean.

O-RING (P16)

ORIFICE

PLATE

COVER

PLATE

HEX. HOLE SCREW

ORIFICE

ASSEMBLY

HOLDING

SCREW

O-RING (P20)

F10-2.ai

CROTCHET JOINT

Figure 7.2 Orifice System

1)   Suspend the supply of the sample gas, then blow the gas line with the air.
2)   Remove the crotchet joint.
3)   Turn the holding screw and take out.

4) Pull out slowly to the direction as shown on Figure 10.2.
5) Loosen the set screw by using the hexagonal wrench attached to take out the orifice plate

together with the cover plate. The following is part number of the orifice plate.

Orifice hole (Ø)

Part number

Orifice hole (Ø)

Part number

0.35

G7025XJ

0.80

G7034XJ

0.40

G7026XJ

0.85

G7035XJ

0.45

G7027XJ

0.90

G7036XJ

0.50

G7028XJ

1.0

G7037XJ

0.55

G7029XJ

1.1

G7038XJ

0.60

G7030XJ

1.2

G7039XJ

0.65

G7031XJ

1.3

G7040XJ

0.70

G7032XJ

1.4

G7041XJ

0.75

G7033XJ

1.5

G7042XJ

6) For the cleaning use something like a supersonic cleaner and never insert into the orifice

holes anything like a stick or rod.

7) When the O-rings are worn out, replace them with the spare parts. Part number of O-rings

are Y9114XB (P16) and L9817MT (P20).

8) After the cleaning and replacement are completed, assemble the parts in the reverse order

of the disassembly as mentioned above.

«
...
51
52
53
54
55
...
»

Содержание CM6G


































































Отзывы:

Нет отзывов

Похожие инструкции для CM6G

Бренд: AR Страницы: 8

Бренд: Hanna Instruments Страницы: 9

Бренд: KROHNE Страницы: 56

Бренд: KALEAS Страницы: 64

SoundTrack LxT N/Forcer

Бренд: Larson Davis Страницы: 12

Бренд: Mark-10 Страницы: 26

Бренд: Kipp & Zonen Страницы: 32

Бренд: Raytech Страницы: 7

Бренд: LaserLiner Страницы: 80

Бренд: Vectronics Страницы: 28

AquiTron AT-WFM

Бренд: aquilar Страницы: 20

Бренд: iSTEK Страницы: 15

Бренд: Micro-g LaCoste Страницы: 168

Бренд: OfiTE Страницы: 6

Бренд: Zamel Страницы: 2

Бренд: PCE Americas Страницы: 111

Бренд: SBS Страницы: 59

Бренд: ZyAura Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды