YOKOGAWA CM6G Скачать руководство пользователя страница 56

Страница: 56 / 65

<7. Maintenance>

7-5

IM 11R02A01-02E

5th Edition : Dec. 28, 2016-00

7.3 Check at the Regular Service

7.3.1

Check the Burner Flame

Whether the sample gas is completely burnt or not shall be judged by observing the shape and

the color of the burner flame.

• The shape of the flame for the complete combustion is as shown in Figure 7.7 - (A) of a

shape sharply outlined, and the height of the inner flame is about a half size of the outer

flame.

• When the primary air is too much, the flame becomes, as shown in Figure 7.7 - (B),

flickering and when the secondary air is not sufficient, the flame outline becomes like (B) as

well.

• When the primary air is not sufficient, the color of the flame is clear yellow (C) and

sometimes soots come out.

• When there is any blockade or leakage is the air line, the flame becomes like the shape as

shown in Figure 7.7 - (D).

F11-8.ai

OUTER FLAME

INNER FLAME

（

）

（

）

（

）

（

）

Figure 7.7 Burner Flames

Check the flames of the burner according to the following procedures. As to the adjustment of the

squeezing screw of the primary air and the secondary air and the cleaning of the air distribution

part, ask to our service personnel.

1) Remove the screw (4 pcs) fixing the external pipe, then remove the connectors to the

terminal of the hot junction detecting point.

2) Disassemble the external pipe and take out the jet plate by pulling upward. (The direction to

pull for removal is shown in Figure 7.8 by the sign of arrow).

3) Insert the attached mirror herewith into the ventilator.

4) When you ignite, the flame reflected on the above mirror can be observed from slanting

upside.

5) Assemble the burner by following the procedures above in the reverse order.

Содержание CM6G


































































Результаты поиска

Содержание CM6G

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA CM6G, Руководство пользователя

Результаты поиска

Содержание CM6G

Отзывы:

Бренды по названию

Популярные бренды