YOKOGAWA CM6G Скачать руководство пользователя страница 11

Страница: 11 / 65

<1. Outline>

1-4

IM 11R02A01-02E

6th Edition :May 10, 2019-00

• Orifice Assembly

Name

Q’ty

Remarks

O-Ring

Hexagon Wrench

P16 (Viton) (Y9114XB)

P20 (Silicon) (L9817MT)

Nominal size 1.5 mm

Nominal size 2.5 mm

Gas Density Meter

Gas Density Meter compensates a density value in calorific value measurement.

It is not required for WI measurement.

Converter: GD400G-N-10-N-



/PA

Detector: GD300S-J-



/KU

Measuring range and unit (specific gravity or density) should be specified. See GS 11T3E1-01E

for further information.

Option

You must purchase options separately.

Name

Part no.

Description

Probe

H7800HA

Insertion length 650 mm

Probe

H7800HB

Insertion length 1150 mm

Probe

H7800HC

Insertion length 1650 mm

Fulflo filter

G7043XJ

Element material: Polypropylene

Pore size: 50 μm

Body: SUS 316

Connection: Rc 1/2

Pressure reducing valve

G7008XF

Primary pressure: 15 MPa max.

Secondary pressure: 0 to 200 kPa

Material: Brass

1.3

Standard Systems for Each Application

Application Measurement

System specification

Suffix code*

Town Gas

Without

density

meter

Gas pressure 10 to 20 kPa: Standard

Gas pressure 10 kPa or under: With pump

Gas pressure 100 to 600 kPa: With pressure

reducing value

-S6200

-S6300

-S6400

Calorific value

MJ/Nm

With

density

meter

Gas pressure 10 to 20 kPa: Quake-proof

Gas pressure 10 to 20 kPa: Standard

Gas pressure 10 kPa or under: With pump

Gas pressure 100 to 600 kPa: With pressure

reducing value

-S6110

-S6210

-S6310

-S6410

Steel Mill

Without

density

meter

Gas pressure 8 to 15 kPa: Without preheating

Gas pressure 8 to 15 kPa: With preheating

Gas pressure 8 kPa or under: Without preheating

Gas pressure 8 kPa or under: With preheating

-S6500

-S6600

-S6700

-S6800

Calorific value

MJ/Nm

With

density

meter

Gas pressure 8 to 15 kPa: Without preheating

Gas pressure 8 to 15 kPa: With preheating

Gas pressure 8 kPa or under: Without preheating

Gas pressure 8 kPa or under: With preheating

-S6510

-S6610

-S6710

-S6810

The code is basic for gas pressure and measurement.

Note: A wet sample gas in the town gas application is outside the scope of the standard specifications. Consult

with Yokogawa.

Содержание CM6G


































































Результаты поиска

Содержание CM6G

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA CM6G, Руководство пользователя

Результаты поиска

Содержание CM6G

Отзывы:

Бренды по названию

Популярные бренды