YOKOGAWA CM6G Скачать руководство пользователя страница 3

Страница: 3 / 65

IM 11R02A01-02E

6th Edition :May 10, 2019-00

<INTRODUCTION>

Safety Precautions

Safety, Protection, Modification of the Product

• In order to protect the system controlled by the product and the product itself and ensure

safe operation, observe the safety precautions described in this user’s manual. We assume

no liability for safety if users fail to observe these instructions when operating the product.

• If this instrument is used in a manner not specified in this user’s manual, the protection

provided by this instrument may be impaired.

• If any protection or safety circuit is required for the system controlled by the product or for

the product itself, prepare it separately.

• Be sure to use the spare parts approved by Yokogawa Electric Corporation (hereafter

simply referred to as YOKOGAWA) when replacing parts or consumables.

• Modification of the product is strictly prohibited.

• The following safety symbols are used on the product as well as in this manual.

WARNING

This symbol indicates that an operator must follow the instructions laid out in this manual in

order to avoid the risks for the human body and health including risk of injury, electric shock, or

fatalities. or the damages to instruments. The manual describes what special care the operator

must take to avoid such risks.

CAUTION

This symbol indicates that the operator must refer to the instructions in this manual in order to

prevent the operator or instrument from being injured, or damaged.
The following are signal words to be found only in our instruction manuals.

CAUTION

This symbol gives essential information to avoid damages of soft or hardware, or system failure.

NOTE

This symbol indicates information that complements the present topic.

Warning and Disclaimer

• The product is provided on an “as is” basis. YOKOGAWA shall have neither liability nor

responsibility to any person or entity with respect to any direct or indirect loss or damage

arising from using the product or any defect of the product that YOKOGAWA can not predict

in advance.

Trademark policy

All company or product and product names mentioned in this document are trade names,

trademarks or registered trademarks of their representative companies. In this document,

trademarks or trade names are not indicated with TM or ® as trademark symbols.

Содержание CM6G


































































Результаты поиска

Содержание CM6G

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA CM6G, Руководство пользователя

Результаты поиска

Содержание CM6G

Отзывы:

Бренды по названию

Популярные бренды