YOKOGAWA CM6G Скачать руководство пользователя страница 34

Страница: 34 / 65

<3.Construction and Function>

3-9

IM 11R02A01-02E

5th Edition : Dec. 28, 2016-00

3.4.2

High/Low Alarm Action

Higher and lower alarm limits are set for the amplified thermocouple output, respectively, to

execute a sequence.

The higher alarm limit is the point to alarm the excessive combustion of the burner, which is set to

approximately 120% of the span. The lower alarm limit is the point to alarm the flame extinction

of the burner. You can change the limit by “LOW AL”volume on the front panel of the calorie

detector. However, the lower alarm limit is set to an appropriate value in the final adjustment test

at the factory before shipment.

If the higher or lower limit alarm occurs, the electromagnetic valve (EV) is closed to stop the

supply of gas

3.4.3 Ignition

Press START on the front panel of the calorie detector to start ignition. One cycle of an

ignition constitutes (T1) and (T2). (T1) is when the ignition voltage is applied to the heater

(T1). (T2) is when the voltage is not applied (when using low calorific value, the time when the

preheating voltage is applied). The cycle repeats five times normally. (T1) time and (T2) time

are set independently within the range from approximately 2 to 20 seconds depending on the

measurement range and gas composition.

If the amplified thermocouple output exceeds the lower alarm limit, the burner is determined to

be ignited and the ignition action is stopped even if it is not completed. If the burner is not ignited

even after the ignition voltage is applied five times, the ignition action is stopped after the ignition

voltage is applied for the fifth time. In that case, press START to start the ignition again.
If the burner flame is extinguished in the event of an alarm, after removing the cause of the

failure, press START to start the ignition again. If the alarm occurs due to excessive combustion,

you cannot resume the ignition until the thermocouple output falls below the lower alarm limit (*1).

Indication lamps turn ON or OFF in accordance with each stage of the sequence.

Figure 3.11 shows the ignition sequence for which the lower alarm limit is set to 50%.

Ignition voltage

ALARM lamp

MEAS lamp

Ignition action

Alarm

status

Measurement

status

OFF

Open

Low

T1T2

Time

Thermocouple output

120%

Ignition action starts

Not ignition

Ignitied

Excessive

combustion

Alarm status

(Higher alarm limit)

50%

(Lower alarm limit)

IGNIT lamp

Ignition action

Figure 3.11 Ignition Sequence

Содержание CM6G


































































Результаты поиска

Содержание CM6G

Отзывы:

Похожие инструкции для CM6G

Бренды по названию

Популярные бренды

YOKOGAWA CM6G, Руководство пользователя

Результаты поиска

Содержание CM6G

Отзывы:

Похожие инструкции для CM6G

Бренды по названию

Популярные бренды