YOKOGAWA AQ2200 Series Скачать руководство пользователя страница 85

Страница: 85 / 183

Connecting the Power Cord

Check that the power switch is off.

Connect the power cord plug to the power inlet on the rear panel.

Connect the other end of the cord to an outlet that meets the following conditions.

Use a grounded three-prong outlet.

Rated supply voltage

100 to 240 VAC (auto switching)

Rated supply frequency

50/60 Hz

Maximum power

consumption

AQ2211: 170 VA; AQ2212: 580 VA (including installed modules)

* This instrument can use a 100 V or a 200 V power supply. The maximum rated voltage differs

according to the type of power cord. Check that the voltage supplied to the instrument is less

than or equal to the maximum rated voltage of the power cord that you will be using before

use.

AQ2211/AQ2212

Power cord

Three-prong

outlet

Turning the Instrument On

Before Turning On the Power, Check That:

• The instrument is installed properly (see section 2.2, “Installing the Instrument”).
• The power cord is connected properly (see the previous page).

Turning the Instrument On

Press the front panel power switch.

2.8 Connecting to the Power Supply

2-26

IM 735101-01EN

Содержание AQ2200 Series
























































































































































































Результаты поиска

Содержание AQ2200 Series

Отзывы:

Похожие инструкции для AQ2200 Series

Бренды по названию

Популярные бренды

YOKOGAWA AQ2200 Series, Руководство пользователя

Результаты поиска

Содержание AQ2200 Series

Отзывы:

Похожие инструкции для AQ2200 Series

Бренды по названию

Популярные бренды