manualshive.com logo in svg

YOKOGAWA AQ2200 Series, Руководство пользователя

Серия Yokogawa AQ2200 - это высокотехнологичные измерительные приборы, предназначенные для различных областей применения. Чтобы получить пользовательское руководство бесплатно, загрузите его с manualshive.com. Наслаждайтесь функциональностью и надежностью этих приборов для успешного выполнения измерительных задач.

Поделиться
Скачать
background image

TLS Module

Code Error Message Description

Corrective Action

1130 Temperature 

Error

The temperature inside the module is 

too high.

Turn the power off and confirm that the frame controller’s inlet 

and exhaust holes are not blocked. After waiting for some 

time, restart the instrument. If the same message continues to 

appear, servicing is required.

1131 Update Error

A failure occurred during a software 

update.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1133 TEC Temperature 

Error

The thermistor detected a temperature 

error.

Turn the power off and confirm that the frame controller’s inlet 

and exhaust holes are not blocked. After waiting for some 

time, restart the instrument. If the same message continues to 

appear, servicing is required.

1134 TEC Over Current 

Error

The thermistor drive current is 

abnormal.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1135 TEC Driver 

Temperature 

Error

The thermistor driver detected a 

temperature error.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1136 LD Over Current 

Error

The LD drive current is abnormal.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1137 TLS EL Error

A TLS end limit error occurred.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1138 TLS Initialization 

Error

A failure occurred during initialization. If the same message continues to appear even after you restart 

the instrument, servicing is required.

1139 TLS WL 

Calibration Error

An error occurred during wavelength 

calibration.

Leave the optical output turned on for at least 30 minutes to 

warm up the instrument. If the same message continues to 

appear, restart the instrument. If the same message continues 

to appear even after you restart the instrument, servicing is 

required.

1135 TEC Driver 

Temperature 

Error

The thermistor driver detected a 

temperature error.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1140 APC PD Feed 

Back Error

The photodiode’s automatic power 

control is malfunctioning.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1141 Gas Cell PD 

Feed Back Error

The wavelength calibration system 

that uses the internal gas cell is 

malfunctioning.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1151 ATT EL Error

The internal attenuator is 

malfunctioning.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1152 ATT Initialization 

Error

A failure occurred during the 

initialization of the internal attenuator.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1153 OSW Switching 

Error

The internal optical switch is 

malfunctioning.

If the same message continues to appear even after you restart 

the instrument, servicing is required.

1157 Wavelength Over 

Error

A wavelength was set that does not 

fall within the settable range.

Check the wavelength. Set the wavelength to a value that falls 

within the settable range.

1159 LD is inactive

The optical output is not active.

Turn the optical output on.

1160 Temperature Limit 

Error

The temperature inside the module is 

too high.

Turn the power off and confirm that the frame controller’s inlet 

and exhaust holes are not blocked. After waiting for some 

time, restart the instrument. If the same message continues to 

appear, servicing is required.

1161 Memory Check 

Error

The internal memory is malfunctioning. If the same message continues to appear even after you restart 

the instrument, servicing is required.

1162 Opt Lock Error

The optical output is locked.

Unlock the optical output.

1163 Sweep Parameter 

Error1

The sweep start wavelength is larger 

than the sweep stop wavelength.

Check the sweep start wavelength, and set it again.

1164 Sweep Parameter 

Error2

The number of sweep steps is 20001 

or more in the Swept application.

Set the number of sweep steps to a value less than or equal to 

20000.

1165 Sweep Parameter 

Error3

The sweep speed is set to a speed at 

which sweeps cannot be performed.

Check the sweep speed, and set it again.

4.2  Error Messages

4-10

IM 735101-01EN

Содержание AQ2200 Series
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AQ2200 Series

M3S Triton Description Handbook preview
Triton
Бренд: M3S Страницы: 40
PAT DS 350 Troubleshooting Manual preview
DS 350
Бренд: PAT Страницы: 57
Nagano Keiki GC31 Instruction Manual preview
GC31
Бренд: Nagano Keiki Страницы: 25
Magnescale DF805SR Instruction Manual preview
DF805SR
Бренд: Magnescale Страницы: 2
Datakom DKM-405 Manual preview
DKM-405
Бренд: Datakom Страницы: 27
Clavia Nord C1 Service Manual preview
Nord C1
Бренд: Clavia Страницы: 13
Lafayette Instrument J00105 User Instructions preview
J00105
Бренд: Lafayette Instrument Страницы: 12
CAME BlueForce Smart Instructions For Use Manual preview
BlueForce Smart
Бренд: CAME Страницы: 24
PKP DTL06 Instruction Manual preview
DTL06
Бренд: PKP Страницы: 7
Percussion Play PPMIRC Installation Instructions preview
PPMIRC
Бренд: Percussion Play Страницы: 3
Kawai Digital Piano CN41 Owner'S Manual preview
Digital Piano CN41
Бренд: Kawai Страницы: 80
LCR LQ-9101 User Manual preview
LQ-9101
Бренд: LCR Страницы: 32
Apera Instruments 28APE190008/AI481 Instruction Manual preview
28APE190008/AI481
Бренд: Apera Instruments Страницы: 13
TE Connectivity 805M1 Operation Manual preview
805M1
Бренд: TE Connectivity Страницы: 5
Xylem MJK MagFlux Series Manual preview
MJK MagFlux Series
Бренд: Xylem Страницы: 179
jacarta iMeter Master User Manual preview
iMeter Master
Бренд: jacarta Страницы: 44
Bushnell 201740 Manual preview
201740
Бренд: Bushnell Страницы: 64
Bender CMD420-DM Manual preview
CMD420-DM
Бренд: Bender Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды