YOKOGAWA 701715 Скачать руководство пользователя страница 415

Страница: 415 / 454

16-11

IM 701730-01E

Troubleshooting, Maintenance, and Inspection

16.5 Replacing the Power Fuse

WARNING

• To prevent electric shock or fires, use a fuse of the specified rating in terms of

current, voltage, and type.

• Always turn OFF the power switch and unplug the power cord before attempting

to replace the fuse.

• Do not short the fuse holder.

Specified Rating

The specifications for power fuses that can be used by the instrument are as follows.

Item

Description

Maximum rated voltage

250 V

Maximum rated current

4 A

Type

Time lag

Standard

VDE/SEMKO/UL/CSA certified.

Part No.

A1352EF

Exchanging the Fuse

Replace the power fuse according to the following steps.

Turn OFF the main power switch on the rear panel.

Unplug the power cord from the power connector.

Insert the tip of a flathead screwdriver into the indentation on the fuse holder

located on the rear panel. Turn the fuse holder and remove it.

Remove the blown fuse from the tip of the fuse holder.

Insert a new fuse into the fuse holder, then return the fuse holder to its original

location on the instrument.

PER

IPHE

RAL

USB

ISM

-A

N200

IN PO

100-1

20V

/220

-240V

250V

A M

50/6

0Hz

250V

T C

LOC

K IN

EXT

TRIG IN

TRIG GA

TE IN

0Vpk 1M

GO/

-G

E PO

TL )

OFF

LINK

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды