YOKOGAWA 701715 Скачать руководство пользователя страница 215

Страница: 215 / 454

10-15

IM 701730-01E

Analyzing and Searching Waveforms

Setting the Search Target Waveform, Level, Slope, and Hysteresis for Detecting

Edges

Use

jog shuttle & SELECT

to select the search target waveform (Source box).

Use

jog shuttle & SELECT

to set the level for detecting the edge (Level box).

Use

jog shuttle & SELECT

to select which slope edge, rising or falling, is to be

detected (Polarity box).

Use

jog shuttle & SELECT

to set the hysteresis (width of the level for detecting

the edge, Hysteresis box).

Setting the Edge Detection Count and the Search Start Point

Use

jog shuttle & SELECT

to set the edge detection count (Count box).

10.

Use

jog shuttle & SELECT

to set the search start point (Start Point box).

11.

Press

ESC

. The Setup dialog box closes.

Select the search target waveform.
Set the level for detecting the edge.
Select which slope edge, rising or falling, is to be detected.

Set the hysteresis (width of the level for detecting the edge).
Set the edge detection count.
Set the search start point.

Selecting the Window for Displaying the Searched Waveform (Zoom Waveform

Display Frame)

This menu appears only when the zoom waveform display mode is set to Z1&Z2 or

Main&Z1&Z2. For all other modes, the menu does not appear, because the selection is

not necessary.

12.

Press the

Result Window

soft key to select Z1 or Z2.

Executing/Aborting the Search

13.

Press the

Exec

soft key. The search is executed, and the word Exec changes to

Abort. Each time a waveform that matches the search condition is detected, the

search is aborted, and the word Abort changes to Exec.

To abort the search, press the

Abort

soft key. The search is aborted, and the word

Abort changes to Exec.

When a waveform that matches the search condition is detected, the zoom box moves to

that position and the zoom waveform display frame (the zoom waveform display frame

selected in step 12 if the zoom waveform display mode is Z1&Z2 or Main&Z1&Z2) shows

the detected waveform zoomed.

14.

To search the next waveform using the same search condition, repeat step 13. The

search can be repeated to the right edge of the screen or up to 1000 detections.

10.4 Searching Waveforms Using the Search and Zoom Function

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды