YOKOGAWA 701715 Скачать руководство пользователя страница 350

Страница: 350 / 454

13-14

IM 701730-01E

Setting the Transmission Time of Periodic Mail

(For action mail, see “Setting Conditions for Sending Mail (Action Mail)” on the next

page.)

Use

jog shuttle & SELECT

to enter the MailBaseTime (time when mail is to be

sent).

Use

jog shuttle & SELECT

to set the Interval (interval for sending mail) in the

range of 1h to 24h. If you are only using action mail, set this to OFF.

Enter the time to send mail.
You can set the interval for sending
mail in the range of 1h to 24h.

Sending a Test Mail

10.

Turn the

jog shuttle

to move the cursor to Mail Test and press SELECT to send a

test mail to the specified recipient.

Sends mail to the specified
mail recipient.

Setting the Conditions for Sending Mail (Action Mail)

Perform steps 1 to 6 on the previous page.

A mail is sent when the following conditions are met.

• When a Trigger Is Activated

For the setup procedure, see section 6.15.

• Through GO/NO-GO Determination

For the setup procedure, see sections 10.9 and 10.10.

Note

•

The sender (From) address of the mail messages sent by the instrument is the same as the

specified recipient address.

•

If the transmitted contents indicate error logs, the most recent error is at the top of the error

log.

•

To use this function, you must configure TCP/IP according to the procedure given in section

13.2.

•

If you set Interval to OFF, periodic mail is not sent.

13.5 Sending Periodic or Action Mail (SMTP Client Function)

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды