YOKOGAWA 701715 Скачать руководство пользователя страница 279

Страница: 279 / 454

11-8

IM 701730-01E

Explanation

You can print the screen image to a USB printer via the USB PERIPHERAL interface.

Connecting the Instrument and the USB Printer

USB PERIPHERAL Connector

To connect a USB printer to the instrument, connect a USB cable to the USB

PERIPHERAL connector. There are two USB PERIPHERAL connectors (ports).

Port 1

Port 2

1 2 3 4

Pin No.

Signal Name

VBUS:

+5 V

D-

+Data

D+

-Data

GND:

Ground

Printers That Can Be Used

USB printers conforming to USB Printer Class Version 1.0 that support the following print

formats can be used.

Note

•

Connect only the printers that are allowed.

•

For details on USB printers that have been tested for compatibility, contact your nearest

YOKOGAWA dealer.

Connection Procedure

When connecting a USB printer, directly connect the printer to the instrument using a

USB cable as shown below. You can connect the USB cable regardless of the power

ON/OFF state of the instrument (supports hot-plugging). Connect the type A connector of

the USB cable to the instrument; connect the type B connector to the printer. When the

power switch is ON, the printer is detected and enabled approximately six seconds after

it is connected.

DL1700E

Printer

USB PERIPHERAL

Note

•

Connect the printer directly without going through a hub.

•

Do not connect USB devices other than USB keyboard, USB mouse, USB printer, and USB

storage that can be used to the USB PERIPHERAL connector.

•

Do not connect multiple printers to the USB PERIPHERAL connector.

•

Do not turn OFF the printer or remove the USB cable while the printer is printing.

•

Do not connect or disconnect the USB cable after the power is turned ON until key operation

is ready (approximately 20 to 30 s).

11.3 Printing Using a USB Printer

Содержание 701715







































































































































































































































































































































































































































































Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды

YOKOGAWA 701715, Руководство пользователя

Результаты поиска

Содержание 701715

Отзывы:

Похожие инструкции для 701715

Бренды по названию

Популярные бренды