YASKAWA S-V Series, Руководство пользователя

Страница: 171 / 311

5.5 One-parameter Tuning (Fn203)
5-33
5
Adjustments
5.5.2
One-parameter Tuning Procedure
The following procedure is used for one-parameter tuning.
Operation procedures will vary in accordance with the tuning mode being used.
• When the tuning mode is set to 0 with priority given to stability or when the tuning mode is set to 1 with pri-
ority given to responsiveness, refer to (1) Setting the Tuning Mode to 0 or 1 .
• When the tuning mode is set to 2 or 3 for adjustments in positioning, refer to (2) Setting the Tuning Mode to
2 or 3 .
One-parameter tuning is performed from the Digital Operator (option) or S.
The operating procedure from the Digital Operator is described here.
For basic operations of the Digital Operator, refer to the
Σ
-V series User’s Manual, Operation of Digital Oper-
ator (SIEP S800000 55).
(1) Setting the Tuning Mode to 0 or 1
Step Display after Operation Keys Operation
1
Press the Key to view the main menu for the
utility function mode.
Use the
or Key to move through the list,
select Fn203.
2
Press the Key to display the mass ratio set in
Pn103 at present. To change the setting, move the
cursor with the
or Key and change the set
value with the or Key.
Note:
If the display does not switch and “NO-OP” is dis-
played, take corrective action after checking the items
given in
5.5.1 (1) Before Performing One-parameter
Tuning.
3
Press the Key to display the initial setting screen
for one-parameter tuning.
4
Press the , or Key and set the items in
steps 4-1 and 4-2.
4-1
„ Tuning Mode Selection
Select the tuning Mode. Select the tuning mode 0 or 1.
Tuning Mode = 0: Makes adjustments giving priority to stability.
Tuning Mode = 1: Makes adjustments giving priority to responsiveness.
4-2
„ Type Selection
Select the type according to the machine element to be driven.
If there is noise or the gain does not increase, better results may be obtained by changing the rigid type.
Type = 1: For belt drive mechanisms.
Type = 2: For ball screw drive mechanisms [Factory setting].
Type = 3: For rigid systems, such as a gear.
5
Input a servo ON command from the host controller.
The display will change from “BB” to “RUN.”
6
Press the Key to display the set value.
㧾㨁㧺ޓ ޓ̆㧲㨁㧺㧯㨀㧵㧻㧺̆
㧲㨚㧞㧜㧞㧦㧾㨑㨒㧭㧭㨀
㧲㨚㧞㧜㧟㧦㧻㨚㨑㧼㨞㨙㨀㨡㨚
㧲㨚㧞㧜㧠㧦㧭㨂㨕㨎ޓ㧿㨡㨜
㧲㨚㧞㧜㧡㧦㨂㨕㨎ޓ㧿㨡㨜
㧮 㧮 ̆ 㧻 㨚 㨑 㧼 㨞 㨙 㨀 㨡 㨚̆
㧼 㨚 㧝 㧜 㧟 㧩 㧜 㧜 㧟 㧜 㧜
Status Display
㧮 㧮 ̆ 㧻 㨚 㨑 㧼 㨞 㨙 㨀 㨡 㨚̆
㧿 㨑 㨠 㨠 㨕 㨚 㨓
㨀 㨡 㨚 㨕 㨚 㨓 㧹 㨛 㨐 㨑 㧩 㧞
㨀 㨥 㨜 㨑 㧩 㧞
㧮 㧮 ̆ 㧻 㨚 㨑 㧼 㨞 㨙 㨀 㨡 㨚̆
㧿 㨑 㨠 㨠 㨕 㨚 㨓
㨀 㨡 㨚 㨕 㨚 㨓 㧹 㨛 㨐 㨑 㧩 㧞
㨀 㨥 㨜 㨑 㧩 㧞
㧾㨁㧺 ̆㧻㨚㨑㧼㨞㨙㨀㨡㨚̆
㧼㨚㧝㧜㧜㧩㧜㧜㧠㧜㧜
㧼㨚㧝㧜㧝㧩㧜㧜㧞㧜㧜㧜
㧼㨚㧝㧜㧞㧩㧜㧜㧠㧜㧜