Yanmar SA Series Скачать руководство пользователя | Manualshive

Страница: 147 / 170

background image

15. SERVICE THE ELECTRICAL SYSTEM

SA221/324/424 Operation Manual

8. Start the engine of the disabled tractor.
9. Run the engine of both disabled and abled

tractors for several minutes.

10.Check the alternator/battery charging light of the

disabled tractor.

11.Carefully disconnect the booster cables:

• Perform the disconnection of the booster cables

from the abled and disabled tractors by doing the
reverse of the preceding procedure.

• Make sure to disconnect the negative (–)

booster cable first before the positive (+) booster
cable.

12.Keep running the engine of the disabled tractor

for not less than 10 min.

■

Replace the Accessory Fuses

1. Park the tractor safely and securely.

• For details, see "7. Safe Practices for Parking the

Tractor" on page 1-7.

2. Shut off the engine.
3. Chock all the tires safely and securely.
4. Allow the engine to cool down for several

minutes.

5. Raise the hood.
6. Grip both ends of the fuse holder cover and

remove the cover.

7. Locate the fuses, refer to the illustration shown.
8. Remove the blown fuse from the socket.
9. Check and fix the problem of the blown fuse.
10.Insert the new fuse into the socket.
11.Install the fuse holder cover.
12.Lower the hood.

(A) Fuse holder cover

(1) Memory fuse: 5A
(2) Fuel pump/Warning light fuse: 15A
(3) Hazard fuse: 10A
(4) Starter fuse: 5A
(5) Engine Fuse: 10A
(6) Head light/Tail light fuse: 25A
(7) Accessories fuse: 15A

■

Check the Alternator Fuse and the
Main Fuse

1. Park the tractor safely and securely.

• For details, see "7. Safe Practices for Parking the

Tractor" on page 1-7.

2. Shut off the engine.
3. Chock all the tires safely and securely.
4. Allow the engine to cool down for several

minutes.

5. Raise the hood.
6. Locate the fuses, refer to the illustration shown.
7. Check the fuses.

IMPORTANT

●

If alternator/battery charging light illuminates:
• shut off the engine of the disabled tractor
• contact YOUR LOCAL YANMAR TRACTOR

DEALER for technical assistance

2. Fuses

IMPORTANT

●

Use of a fuse other than a correctly rated one can
damage the electrical system.

●

Replace blown fuse with a new fuse of the same
ampere rating only after fixing the problem.

(A)

ENGINE

10A

HL+TL

25A

ACC

15A

MEMORY

5A

15A

PULLER

5A

10A

HAZARD

10A

START

5A

25A

FL+WA

15A

1A8330-65780

(1)

(2)

(3)

(4)

(5)

(6)

(7)

SA221_324_424_OperatorsManual.book 4 ページ２０１８年６月４日　月曜日　午後５時１９分

«
...
145
146
147
148
149
...
»

Содержание SA Series











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SA Series

Бренд: Kioti Страницы: 111

Бренд: MTD Страницы: 2

Бренд: New Holland Страницы: 2

Northstar 1200UNIV

Бренд: Rankin Страницы: 32

Бренд: Original Tractor Cabs Страницы: 13

Бренд: Curtis Страницы: 28

Бренд: SAME Страницы: 24

Monogram ZCG3100VBB

Бренд: GE Страницы: 2

Boomer 1020/T1010

Бренд: New Holland Страницы: 1

Бренд: Viking Страницы: 10

Zero Turn 73997

Бренд: Classic Accessories Страницы: 3

Бренд: Case Страницы: 26

Бренд: Sulky Страницы: 51

Бренд: Yanmar Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды