Yanmar SA Series Скачать руководство пользователя

Страница: 157 / 170

17-4

17. TROUBLESHOOTING

SA221/324/424 Operation Manual

The engine has no

power

1. A problem in the fuel

1. Fuel system

• Check whether the specification of

the fuel used is correct.

• use correct fuel specification

• Check whether there is water in the

sediment bowl.

• remove the water and clean the

sediment bowl

• Check whether the fuel filter is

clogged.

• replace the fuel filter

• Check whether air is present in the

fuel system.

• bleed air from the fuel system

• Check whether the fuel injection

pump is out of timing.

• contact YOUR LOCAL YANMAR

TRACTOR DEALER

• Check whether the fuel nozzles are

faulty.

• contact YOUR LOCAL YANMAR

TRACTOR DEALER

2. A problem in the cooling

2. Cooling system

• Check whether the air intake for

radiator is clogged.

• clean the air intake for radiator

• Check whether the engine is

overheating.

• contact YOUR LOCAL YANMAR

TRACTOR DEALER

• Check whether the coolant

temperature is too low.

• contact YOUR LOCAL YANMAR

TRACTOR DEALER

3. A problem in the lubrication

3. Lubrication system

• Check whether the engine oil

viscosity is high.

• replace engine oil with the specified

viscosity

• Check for a clogged in the crankcase

ventilation tube.

• contact YOUR LOCAL YANMAR

TRACTOR DEALER

4. A problem in the engine mechanical

4. Engine mechanical system

• Check whether the valve clearance is

correct.

• contact YOUR LOCAL YANMAR

TRACTOR DEALER

The problem is:

The possible cause(s) are:

Remedy:

SA221_324_424_OperatorsManual.book 4 ページ２０１８年６月４日　月曜日　午後５時１９分

Содержание SA Series











































































































































































Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды

Yanmar SA Series, Руководство по эксплуатации

Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды