Yanmar SA Series Скачать руководство пользователя

Страница: 122 / 170

14. PERIODIC SERVICE

14-10

SA221/324/424 Operation Manual

■

Inspection Procedure for the Safety
System

Before operating the tractor, ALWAYS:

●

Get familiarized with the operation of the tractor.

●

Perform the safety checks on the tractor's safety
interlock system.

If a problem is detected on the safety interlock
system:

●

Do not attempt to operate the tractor.

●

Contact YOUR LOCAL YANMAR TRACTOR
DEALER for technical assistance.

1. Power Take Off (PTO) Switch

1. Sit on the operator seat.
2. Engage the parking brake securely, for details,

see "6. Lock and Set the Parking Brake" on page
7-3.

3. Release the forward and reverse drive pedal to N

(neutral) position.

4. Pull up Power Take Off (PTO) switch to ON

position.

5. Turn the starter key switch to the START position.

(A) Power Take Off (PTO) switch

6. Confirm that the starter motor does not operate.
7. Push down Power Take Off (PTO) switch to OFF

position.

8. Activate the starter motor to start the engine.

●

Read the DANGER, WARNING and CAUTION
statements on the safety alert decals on the
tractor.

●

Before starting the engine:
• remain seated on the operator seat
• release the forward and reverse drive pedal

to N (neutral) position

• always move the range shift lever to the N

(neutral) position

• push down Power Take Off (PTO) switch to

OFF position

• never attempt to start the engine while the

operator is still on the ground

●

Engine exhaust gas contains carbon
monoxide.
• if inhaled, the engine exhaust gas can cause

severe poisoning or even death

●

Always perform the safety checks in a well
ventilated area.

●

When working in an enclosed area, always
expel the engine exhaust gas to an outdoor
area.
• connect one end of an extension pipe to the

engine exhaust pipe

• set the other end outside of the work area

●

Allow fresh outside air to flow into an
enclosed work area to remove the engine
exhaust gas from the area.

! WARNING

NEVER inhale the engine

exhaust gas.

NOTE

●

The engine must not crank when Power Take Off
(PTO) switch is in ON position.

(A)

SA221_324_424_OperatorsManual.book 10 ページ２０１８年６月４日　月曜日　午後５時１９分

Содержание SA Series











































































































































































Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды

Yanmar SA Series, Руководство по эксплуатации

Результаты поиска

Содержание SA Series

Отзывы:

Похожие инструкции для SA Series

Бренды по названию

Популярные бренды