Curtis 1NHWM25SCA Скачать руководство пользователя страница 1

Страница: 1 / 28

1 of 28

INST

ALLA

TIO

N & OWNER

’

S MANU

New Holland Workmaster 25S

Cab with Heater (p/n: 1NHWM25SCA)

fits tractor models: Workmaster 25S

(*=Not including accessories)

Available Options:

1. Front LED Work Lights (P/N: 9LEDW4)

2. Rear LED Work Lights (P/N: 9LEDW3)

3. Strobe Light (P/N: 9LEDS2)

4. Dome Light (P/N: 9LEDD14)

5. Side View Mirrors (P/N: 9PM5)

6. Rear View Mirror (P/N: 9PM3)

7. Rear Wiper (P/N: 9PWK8512F9

11A)

8. Seal Kit (P/N: 9SK8)

9. Adaptor Kit to Mount Cab Without Loader (P/N: 1NHWM25SAK)

Approximate Installation Time *

Experienced Dealer Technician –

Hours

Average Dealer Technician –

8 Hours

Yourself –

10 Hours

Approximate Product Specifications

Floorboard to Roof Height: 61.625 inches

Weight: 329 lbs.

Cab Width: 47.625 inches (w/o side mirrors)

Rev. B, 08/17/2021

P/N: IM

1NHWM25SCA

The contents of this envelope are the property of the owner. Leave with the owner when installation is complete.

While this cab kit was designed to fit on the vehicle(s) listed above, manufacturing tolerances and vehicle

assembly may affect cab fitment. It is the responsibility of the cab installer to check all vehicle pedals and

levers for full functionality and, as required, adjust the cab fitment to prevent any interference of the cab

components with the travel of pedals or levers.

Front windshield wiper and

heater comes standard

with cab. Also shown with

optional front work lights,

and side view mirrors.

Содержание 1NHWM25SCA





























Результаты поиска

Содержание 1NHWM25SCA

Отзывы:

Похожие инструкции для 1NHWM25SCA

Бренды по названию

Популярные бренды

Curtis 1NHWM25SCA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 1NHWM25SCA

Отзывы:

Похожие инструкции для 1NHWM25SCA

Бренды по названию

Популярные бренды