Curtis 1NHWM25SCA Скачать руководство пользователя страница 7

Страница: 7 / 28

CAB INSTALLATION

7 of 28

Fig. 4.3a (Cowl)

STEP 4: (RADIATOR SHROUD, LOAD

LOCK LEVER & COWL)

4.1

Position the radiator shroud on the vehicle just in front

of the front lip of the floorboard per figure 4.1.

Install Tip:

If needed, move the rubber boot of the jockstick out of

the way when placing the shroud in place. Place the

boot back in place once shroud is placed.

4.2

Install Thumb Screw into previously installed Load Lock

Lever Extension bracket (Step 1.10). Make sure there

is enough thread on the inside for a hex nut to fit. Then

thread and tighten on the hex nut on the inside. See

Figures 4.2a and 4.2b.

Hardware Used

Qty

Thumb Screw, 3 inches long

#10

32 Hex Nut

Tools required

3/8”

Wrench or Socket

4.3

Install steel cowl in front of radiator shroud per figure

4.3a. For best seal, make sure that rubber running

across the top of the dashboard (between the white

arrows) is pushed back and pushed forward as it runs

down the side of the dash (outside the white arrows) as

shown in figure 4.3b.

Hardware Used

Qty

1/4

20 Thumb Nut

Fig. 4.1 (Radiator Shroud, Right)

Lip of floorboard

Boot

Fig. 4.3b (Cowl Rubber)

Push rubber back towards

steering wheel between

the white arrows.

Figure 4.2a (Load Lock Lever, Cab inside)

Figure 4.2b (Load Lock Lever, Cab outside)

#10

32 Hex Nut

Содержание 1NHWM25SCA





























Результаты поиска

Содержание 1NHWM25SCA

Отзывы:

Похожие инструкции для 1NHWM25SCA

Бренды по названию

Популярные бренды

Curtis 1NHWM25SCA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 1NHWM25SCA

Отзывы:

Похожие инструкции для 1NHWM25SCA

Бренды по названию

Популярные бренды