Curtis 1NHWM25SCA Скачать руководство пользователя страница 17

Страница: 17 / 28

CAB INSTALLATION

17 of 28

STEP 22: (DOORS)

22.1

Check to make sure that the brass washers are still

installed on the left side hinge pins and then apply

grease to the pins.

22.2

Hang the left door on the hinge pins.

Note: If necessary, adjust the door as outlined in steps 22.3

thru 22.5.

22.3

Loosen the door hinges to allow for adjustment later.

While lifting up and forward on the door handle, line up

the door latch with the striker pin and carefully attempt

to latch. You should be able to hear 2 clicks as you

slowly engage the latch on the pin. If the latch is too far

forward or back to latch on the pin, adjust as shown.

See Figures 22.3a through 22.3c. Then retighten and

latch.

22.4

Stand back and examine the alignment of the door with

the roof and the A

pillar. You can adjust this by moving

the striker pin up or down as shown to help with

alignment.

TIP: In the final step, the front of the door will

drop a small amount the first time you open it. Set the

front of the door a little bit higher so it aligns properly.

Adjust as necessary until you are happy with the

alignment. Have an assistant sit inside the cab and

once more carefully close the door like you did in step

22.3. Work with the assistant and tighten the hinge

bolts.

22.5

Open the door and check for smooth operation of the

latch. As noted in step 22.4, the door will likely drop a

little bit at the front and the striker pin will need to be

adjusted down accordingly. Also make sure the door

seal is making contact along the perimeter of the door

and the latch clicks twice when closing. If necessary,

adjust the striker in or out to achieve this.

22.6

With the door open, attach a gas strut to the ball studs

on the side frame and door. Make sure the quick

release end is on the side frame so that the gas strut

stays with the door if removed for ventilation.

22.7

Repeat steps 22.1 through 22.6 for the right door.

Fig. 22.3a (Door Hinge Adjustment)

Fig. 22.3b (Striker Pin Adjustment)

Fig. 22.3c (Door Latch Adjustment)

Adjustment

Loosen Door

Hinges

Содержание 1NHWM25SCA





























Результаты поиска

Содержание 1NHWM25SCA

Отзывы:

Похожие инструкции для 1NHWM25SCA

Бренды по названию

Популярные бренды

Curtis 1NHWM25SCA, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 1NHWM25SCA

Отзывы:

Похожие инструкции для 1NHWM25SCA

Бренды по названию

Популярные бренды