Yamato BM500 Скачать руководство пользователя

Страница: 14 / 45

2. PRE-OPERATION PROCEDURES

Prior Confirmation

Bath container water/oil supply precautions.

The bath container installed in main unit is removable for easy filling and draining. Use caution in
regard to the following when adding water or oil.

BM series water bath



Fill so that bath will not overflow when specimen flask(s) is submersed.



Wash bath container regularly with water to keep it clean. Before setup, remove dirt and other

contaminants from bath container interior, and also from the outer surface, especially where heater
and temperature sensor contact the container surface.



Be sure to remove all excess water after washing, and dry outer surface of bath container thoroughly

before use. Allowing water to remain on the outer surface of bath container may cause inaccurate
temperature readings and longer heating times.



Do not place flammable substances inside unit or near heater. A fire or explosion may result.



Clean heater and inside of unit regularly to maintain cleanliness and safety. Malfunction or fire

may result if contaminants are allowed to remain and build up on heater or inside of unit.



To prepare unit for cleaning, turn off power switch, disconnect the power cable and clean ONLY

after confirming that heater and unit have cooled sufficiently.

Oil supply for BO model water bath



Fill with maximum 3 liters of oil. Bath should not overflow when oil is heated and specimen flask(s)

is submersed.



Wash bath container with mild detergent to keep it clean. Before setup, remove dirt and other

contaminants from bath container interior, and also from the outer surface, especially where heater
and temperature sensor contact the container.



Be sure to remove all excess water after washing, and dry outer surface of bath container thoroughly

before use. Allowing water to remain on the outer surface of bath container may cause inaccurate
temperature readings and longer heating times.



Do not place flammable substances inside unit or near heater. A fire or explosion may result.



Clean the heater and inside of unit regularly to maintain cleanliness and safety. Malfunction or fire

may result if contaminants are allowed to remain and build up on heater or inside of unit.



To prepare unit for cleaning, turn off power switch, disconnect the power cable and clean ONLY

after confirming that heater and unit have cooled sufficiently.

Handle with care.

Do not overfill.

Keep bath container, unit and heater clean.

Do not spill bath fluid.

Содержание BM500














































Результаты поиска

Содержание BM500

Отзывы:

Похожие инструкции для BM500

Бренды по названию

Популярные бренды

Yamato BM500, Инструкция по эксплуатации

Результаты поиска

Содержание BM500

Отзывы:

Похожие инструкции для BM500

Бренды по названию

Популярные бренды