Yamato BM500 страница 12 Скачать руководство пользователя

Страница: 12 / 45

2. PRE-OPERATION PROCEDURES

Prior Confirmation

BM500/510 water bath operation precautions:

Exercise caution in regard to the following.

①

Connect unit to a power outlet having sufficient capacity.

②

Do not move unit while in operation.

③

Avoid touching hot surface areas or bath fluid during operation.

④

Do not drain unit until water temperature falls below 45°C.

⑤

Be sure not to spill water on or around unit while adding. Electric shock or fire may result.

⑥

Do not leave unit unattended during operation.

⑦

Use water for bath fluid. Using purified or distilled water is recommended to prevent buildup of

mineral deposits.

⑧

Do not place or operate unit outdoors.

⑨

Turn power OFF when removing bath container from the main unit.

⑩

Do not heat bath container without water.

BO400/410 oil bath operation precautions:

Exercise caution in regard to the following.

①

Connect unit to a power outlet having sufficient capacity. BO400:100 to 120V AC, 12.5A. BO410:

200 to 240V AC, 6.5A.

②

Do not move unit while in operation.

③

Avoid touching hot surface areas or bath fluid during operation.

④

Do not drain unit until oil temperature falls below 45°C.

⑤

Be sure not to spill oil on or around unit while adding. Electric shock or fire may result.

⑥

Do not leave unit unattended during operation.

⑦

Use ONLY silicon oil for bath fluid.

⑧

Do not place or operate unit outdoors.

⑨

Turn power OFF when removing bath container from the main unit.

⑩

Do not heat bath container without oil.

⑪

Be careful not to allow oil to overflow while heating.

Содержание BM500














































Результаты поиска

Содержание BM500

Отзывы:

Похожие инструкции для BM500

Бренды по названию

Популярные бренды

Yamato BM500, Инструкция по эксплуатации

Результаты поиска

Содержание BM500

Отзывы:

Похожие инструкции для BM500

Бренды по названию

Популярные бренды