Yamaha V150 Скачать руководство пользователя | Manualshive

Страница: 69 / 82

background image

Trouble Recovery

64

engine. Use the emergency starter rope
only as instructed. Do not touch the fly-
wheel or other moving parts when the
engine is running. Do not install the
starter mechanism or top cowling after
the engine is running.

●

Do not touch the ignition coil, spark
plug wire, spark plug cap, or other elec-
trical components when starting or op-
erating the motor. You could get an

electrical shock.

EMU29561

Emergency starting engine

1.

Remove the top cowling.

2.

Remove the start-in-gear protection ca-
ble from the starter, if equipped.

3.

Remove the starter/flywheel cover after
removing the bolt(s).

4.

Prepare the engine for starting. For fur-
ther information, see page 30. Be sure
the engine is in neutral and that the en-
gine stop switch lanyard lock plate is at-
tached to the engine stop switch. The
main switch must be “

” (on), if

equipped.

5.

If equipped the choke knob, pull out it
when the engine is cold. After the engine
starts, gradually return the choke knob
to its home position as the engine warms
up.

6.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope several turns
around the flywheel clockwise.

7.

Give a strong pull straight out to crank

ZMU03920

ZMU02334

ON START

OFF

ZMU01906

ZMU03921

«
...
67
68
69
70
71
...
»

Содержание V150



















































































Отзывы:

Нет отзывов

Похожие инструкции для V150

Бренд: TYAN Страницы: 67

Бренд: Sure Electronics Страницы: 32

Бренд: ASROCK Страницы: 95

Бренд: Gigabyte Страницы: 136

Бренд: JETWAY Страницы: 48

Бренд: Honda Страницы: 692

Бренд: Honda Страницы: 152

Бренд: OLIMEX Страницы: 26

Бренд: Vox Страницы: 93

Бренд: Commell Страницы: 29

Бренд: ECS Страницы: 43

Бренд: DFI Страницы: 78

LanParty UT nF3 Ultra-D

Бренд: DFI Страницы: 115

LANParty Jr. GF9400 T2RS

Бренд: DFI Страницы: 138

Бренд: Soyo Computer Страницы: 20

Бренд: JGINYUE Страницы: 14

Бренд: STMicroelectronics Страницы: 2

STEVAL-IFD001V1

Бренд: STMicroelectronics Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды