Yamaha V150 Скачать руководство пользователя | Manualshive

Страница: 17 / 82

background image

Basic components

12

EMU26190

Remote control lever

Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the le-
ver back from neutral engages reverse. The
engine will continue to run at idle until the le-
ver is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.

EMU26201

Neutral interlock trigger

To shift out of neutral, first pull the neutral in-
terlock trigger up.

EMU26211

Neutral throttle lever

To open the throttle without shifting into ei-
ther forward or reverse, put the remote con-
trol lever in the neutral position and lift the
neutral throttle lever.

NOTE:

The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed

position.

1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster

1. Neutral “ ”

2. Forward “ ”

3. Reverse “ ”
4. Shift
5. Fully closed

6. Throttle
7. Fully open

1. Neutral interlock trigger

«
...
15
16
17
18
19
...
»

Содержание V150



















































































Отзывы:

Нет отзывов

Похожие инструкции для V150

Бренд: AKM Страницы: 34

Бренд: Gigabyte Страницы: 40

Бренд: Gigabyte Страницы: 51

Бренд: ST Страницы: 77

Бренд: ST Страницы: 11

970 Extreme3 R2.0

Бренд: ASROCK Страницы: 70

Бренд: Texas Instruments Страницы: 25

Бренд: P&E Microcomputer Systems Страницы: 38

Бренд: Atmel Страницы: 16

Бренд: Advantech Страницы: 4

Track bq27520EVM

Бренд: Texas Instruments Страницы: 22

Бренд: Analog Devices Страницы: 17

Бренд: Supermicro Страницы: 93

Бренд: Aura Light Страницы: 8

Бренд: Supero Страницы: 143

BD7F100EFJ-EVK-002

Бренд: Rohm Страницы: 6

Бренд: Gigabyte Страницы: 96

Бренд: Seanix Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды