manualshive.com logo in svg

Yamaha V150, Руководство пользователя

Поделиться
Скачать
Yamaha V150 Скачать руководство пользователя страница 68

 

Trouble Recovery

 

63

NOTE:

 

Consult your Yamaha dealer if the new fuse

 

immediately blows again.

 

EMU29522

 

Power trim and tilt / power tilt will not 
operate

 

If the engine cannot be tilted up or down with
the power trim and tilt / the power tilt because
of a discharged battery or a failure with the
power trim and tilt unit / the power tilt unit, the
engine can be tilted manually.
1.

Loosen the manual valve screw by turn-
ing it counterclockwise until it stops.

2.

Put the engine in the desired position,
then tighten the manual valve screw by

turning it clockwise.

 

EMU29532

 

Starter will not operate

 

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

 

EWM01021 

 

●

 

Use this procedure only in an emergen-
cy to return to the nearest port for re-
pairs.

 

●

 

When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not oper-
ate. Make sure the remote control lever
is in neutral. Otherwise the boat could
unexpectedly start to move, which
could result in an accident.

 

●

 

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating the
boat.

 

●

 

Do not attach the lanyard to clothing
that could tear loose. Do not route the
cord where it could become entangled,
preventing it from functioning.

 

●

 

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-
gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the
boat to be thrown forward.

 

●

 

Make sure no one is standing behind
you when pulling the starter rope. It
could whip behind you and injure
someone.

 

●

 

An unguarded, rotating flywheel is very
dangerous. Keep loose clothing and
other objects away when starting the

 

1. Fuse holder
2. Fuse (20 A, 30 A)

1. Manual valve screw

1

2

ZMU03919

ZMU03464

1

Содержание V150



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды