Yamaha V150 Скачать руководство пользователя

Страница: 26 / 82

Basic components

tor switch.

NOTE:

The fuel level reading can be affected by the
position of the sensor in the fuel tank and the
attitude of the boat in the water. Operation
with bow-up trim or continuous turning can

give false readings.

EMU26720

Fuel warning indicator

If the fuel level decreases to one segment,
the fuel level warning segment will begin to
blink.

CAUTION:

ECM00880

Do not continue to operate the engine
with full throttle if a warning device has
activated. Get back to the port within troll-

ing engine speed.

EMU26730

Low battery voltage warning
indicator

If battery voltage drops, the display will auto-
matically turn on and begin to blink.

CAUTION:

ECM00870

Get back to the port soon if a warning de-
vice has activated. For charging the bat-

tery, consult your Yamaha dealer.

EMU26801

Warning system

CAUTION:

ECM00090

Do not continue to operate the engine if a
warning device has activated. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

EMU26816

Overheat warning

This engine has an overheat warning device.
If the engine temperature rises too high, the
warning device will activate.

Activation of warning device

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

If equipped with an overheat warning indi-
cator, it will light or blink.

1. Fuel level warning segment

ZMU01745

1. Low battery indicator

Содержание V150



















































































Результаты поиска

Содержание V150

Отзывы:

Похожие инструкции для V150

Бренды по названию

Популярные бренды

Yamaha V150, Руководство пользователя

Результаты поиска

Содержание V150

Отзывы:

Похожие инструкции для V150

Бренды по названию

Популярные бренды