Yamaha V150 Скачать руководство пользователя

Страница: 43 / 82

Operation

Push the power trim and tilt switch / pow-
er tilt switch “

” (down) to lower the out-

board motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28185

Procedure for power trim and tilt / power
tilt models

Place the remote control lever / gear
shift lever in neutral.

Slightly tilt the outboard motor up to the
desired position using the power trim
and tilt switch / power tilt switch.

ZMU03453

ZMU01936

ZMU03524

ZMU03525

Содержание V150



















































































Результаты поиска

Содержание V150

Отзывы:

Похожие инструкции для V150

Бренды по названию

Популярные бренды

Yamaha V150, Руководство пользователя

Результаты поиска

Содержание V150

Отзывы:

Похожие инструкции для V150

Бренды по названию

Популярные бренды