manualshive.com logo in svg

Yamaha V150, Руководство пользователя

Поделиться
Скачать
Yamaha V150 Скачать руководство пользователя страница 24

 

Basic components

 

19

 

turning on the main switch to make sure all

 

segments come on.

NOTE:

 

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired unit of measurement by set-
ting the selector switch on the back of the

 

gauge. See the illustration for settings.

 

EMU26610

 

Trim meter

 

This gauge shows the trim angle of your out-
board motor.

NOTE:

 

Memorize the trim angles that work best for
your boat under different conditions. Adjust
the trim angle to the desired setting with the

 

power trim and tilt switch.

 

EMU26620

 

Trim meter (digital type)

 

This meter shows the trim angle of your out-
board motor.

NOTE:

 

●

 

Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired using
the power trim and tilt switch.

 

●

 

If the trim angle of your motor exceeds the
trim operating range, the top segment on

 

the trim meter display will blink.

 

EMU26650

 

Hour meter (digital type)

 

This meter shows the number of hours the
engine has been run. It can be set to show
the total number of hours or the number of
hours for the current trip. The display can
also be turned on and off.

 

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

ZMU04581

ZMU01869

ZMU01870

Содержание V150



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды